Standard Offset Brick Extension for Ring Removable Battery Doorbells (2/3/3+/4)
Compatibility: Ring Doorbells with REMOVABLE Battery ONLY!
-
Fits ONLY: Ring models where the battery pack can be fully removed for charging. This includes:
- Ring Video Doorbell 2 (NOT GEN2)
- Ring Video Doorbell 3 / 3 Plus
- Ring Video Doorbell 4
- (Does NOT fit Battery Doorbell Plus or Pro models which have different bodies)
- Confirm your model looks like this (requires removing bottom cover to access screws):
-
(Example Images - Click first for Amazon Link. As an Amazon Associate, I earn from qualifying purchases.) - WILL NOT FIT: Ring models with Integrated Batteries (Gen 1, Gen 2 2020), or ANY Pro/Plus/Wired models.
- Surface Width: Requires mounting surface (trim/molding) to be AT LEAST 9/16 inches wide for the base.
Unsure? Send us a photo! Check our Ring Model Guide or contact us!
Extend Your Ring Battery Doorbell Past Brick with Standard Offset!
Is your Ring Doorbell (2, 3, 3 Plus, or 4) mounted on trim set back from brick or stone? Need more clearance for a storm door? This **Standard Offset Brick Extension Mount** brings your doorbell forward for better visibility and provides a moderate sideways shift.
Installs easily onto your existing trim (minimum 9/16" wide) without drilling into brick, positioning your removable-battery Ring doorbell correctly relative to the brick face.
How it Works: Standard Offset (5/8")
This mount uses our popular STANDARD OFFSET. The center of your Ring Doorbell will be shifted approximately 5/8 inches horizontally towards the brick side relative to the center of the narrow 9/16" base. This leaves about 3/8 inch of the base visible near the door frame.
This configuration provides good clearance and viewing angles for many installations, positioning the doorbell partially over the adjacent brick.
This mount positions the doorbell over or in front of the brick face.
Standard Offset (This Product) vs Full Offset:

Need Maximum Sideways Clearance? Click here for the Full Offset version for these models.
Base Dimensions & Mounting: The extension base is 9/16 inches wide (requires >= 9/16" surface). Standard mounting hole spacing is 2.5 inches (center-to-center). Ensure solid mounting on trim. Wall-mounting screws not included.
Angled Trim? If your trim is angled, add our Angle Shims (sold separately) for a perpendicular installation.
CRITICAL: Measure & Select Your Extension Length!
Choose the correct length to clear your brickwork or storm door. Measure carefully:
- Measure the exact distance straight out from the surface where the mount base will attach (your trim) to the outermost face of your brick or obstacle.
- Order THIS measurement as your required Extension Length. (Do NOT subtract doorbell thickness for offset mounts).
Select the required extension length from the dropdown menu when ordering. (Starts at 1/4 inch).
Need help measuring? Text/email a picture! (Contact info below)
Key Features & Benefits:
- Fits Ring Removable Battery Models: Compatible with Ring Video Doorbell 2, 3, 3 Plus, and 4.
- Standard 5/8" Offset: Provides good sideways positioning for most common needs, including storm door clearance.
- "Over Brick" Placement: Extends doorbell forward past brick, positioning it partially over the brick face.
- Avoid Drilling Brick: Mounts to existing trim (>=9/16" wide, Std. 2.5" hole spacing).
- Selectable Extension Length: Order the precise depth needed (Trim-to-Brick/Obstacle measurement).
- Narrow Base (9/16" Std): Fits most standard trim widths.
- Wire Passthrough: Internal channel accommodates optional hardwiring.
- Durable PETG Construction: Strong, weather-resistant plastic.
- Add-on Compatible: Works with angle shims, fillers etc. (see below).
- Future-Proof Bracket: Top adapter bracket is replaceable for future upgrades (available here).
How to Install Your Standard Offset Extension
This mount uses two main printed pieces: the Extension Base and the Doorbell Adapter Bracket.
-
Tools & Prep: Gather: Drill, PH1 & PH2 Philips Screwdrivers/Bits, Level, Anchors (if needed), Ring security screwdriver (often orange, from doorbell box).
Turn OFF power at the breaker if hardwiring! Ensure battery is charged but removed during install.
-
Mount Extension Base: Position the Extension Base (correct length/offset) on trim over wires. Attach securely using appropriate screws (#6 size likely, use PH2) and anchors into the 2.5" spaced holes.
Ensure base is level. Don't overtighten.
-
Attach Doorbell Adapter Bracket: Route wires through the Doorbell Adapter Bracket. Align onto Extension Base. Attach using the four small center screws provided (likely #4 screws / PH1 driver).
Use correct PH1 bit. Tighten until flush. Check for/clear debris if needed. Do NOT over-torque.
- Wire Doorbell (If Hardwiring): Connect wires to your Ring Doorbell following Ring's instructions. Tuck excess wire.
-
Attach Ring Doorbell:
- Take the main body of your Ring Doorbell (with battery removed, faceplate off).
- Align the mounting holes on the back of the doorbell body with the holes on the Doorbell Adapter Bracket.
- Secure the **doorbell body** to the Adapter Bracket using the small screws PROVIDED WITH THIS MOUNT (typically #4 / PH1 driver). Do NOT use Ring's longer wall screws here.
- Re-install the battery (if not hardwired) and snap the Ring faceplate back on. Secure with Ring's security screw(s) at the bottom using the Ring screwdriver.
Use correct drivers/tools for each screw type. Tighten gently. - Final Check & Power On: Ensure doorbell is secure. Turn power back on (if applicable) and test.
Follow safety rules & Ring's guidelines. Use correct anchors/screws. Correct screwdriver size prevents stripping.
Enhance Your Home Security Experience
Why Choose the Brick Extension?
This extension is designed specifically for Ring battery doorbells (2/3/3+/4) allowing optimal placement when mounting near brick. The standard 5/8" offset improves visibility and functionality, overcoming challenges posed by recessed trim or new storm doors, enhancing accessibility and security.
Simple Installation with Reliable Materials
Crafted from high-quality PETG, this brick extension ensures durability. Installation onto existing trim is straightforward, avoiding complex masonry drilling, making it suitable for DIY setup.
Upgrade Your Home Security
Extending and offsetting your doorbell improves aesthetics and enhances security by providing a clearer, wider view for your camera. Ensure your Ring doorbell effectively monitors your entryway.
Optional Add-ons & Accessories:
Further customize your installation:
-
Angle Shims (5°, 10°, 15°)
Corrects for angled trim *under the Extension Base*.
-
Horizontal Angle Adapter or Swivel Add-on
Add horizontal angle adjustment to the end of the extension.
-
Bottom Filler Spacer Plate
Fills the gap below the extension base on angled/uneven trim.
-
Body Shim Filler Plate
Fills gaps between the extension body and uneven brick.
-
Add Side Wire Entry
Adds side entry holes ("mouse holes") to the *Extension Base* (add service to cart).
Product Examples
(See listing photos for details or contact us for more examples!)
Need Help? Confirm Compatibility & Measurements!
Ensure you have a compatible Ring Removable Battery model (2, 3, 3+, 4). Need help measuring extension length?
- Email: shop@doorbellmount.com (Send Pictures!)
- Text/Call: 1-833-326-6868 (Text Pictures! Corrected Number)
Standard Color: Black. For other colors, add the Color Change Request item.
Doorbell Not Included. Includes the 2-piece extension mount (Extension Base + Doorbell Adapter Bracket) and necessary assembly screws.
PETG Material: Printed in durable, outdoor-rated PETG.
3D Printed Quality: Minor cosmetic variations inherent to 3D printing may exist but do not affect function. Contact us with quality concerns before reviewing.
Order the Standard Offset Brick Extension for your Ring Doorbell (2, 3, 3+, 4) today! Remember to measure carefully (Trim to Brick Face!) and select your required extension length.