Standard Offset Brick Extension for Ring Battery Doorbell Plus (& 2/3/4)
Compatibility: Ring Battery Doorbell Plus & Similar REMOVABLE Battery Models!
- Primary Fit: Ring Battery Doorbell Plus.
- Also Fits: Other Ring models using the same body style with a REMOVABLE battery (Ring 2, Ring 3, Ring 3 Plus, Ring 4).
- Confirm your model uses a removable battery & this mounting pattern:
-
(Example Images) - WILL NOT FIT: Ring Wired Doorbell **Pro**, Ring models with Integrated Batteries (Gen 1, Gen 2 2020), or ANY Wired only models.
- Surface Width: Requires mounting surface (trim/molding) to be AT LEAST 9/16 inches wide for the base.
Unsure? Send us a photo! Check our Ring Model Guide or contact us!
Extend Your Ring Battery Doorbell Plus Past Brick with Standard Offset!
Is your Ring Battery Doorbell Plus (or similar removable battery model like Ring 2/3/4) mounted on trim set back from brick or stone? Need clearance for a storm door? This **Standard Offset Brick Extension Mount** brings your doorbell forward and provides a moderate sideways shift.
Installs easily onto your existing trim (minimum 9/16" wide) without drilling into masonry, positioning your doorbell correctly relative to the brick face.
How it Works: Standard Offset (5/8")
This mount features our popular STANDARD OFFSET. The center of your Ring Doorbell will be shifted approximately 5/8 inches horizontally towards the brick side relative to the center of the narrow 9/16" mount base. This typically leaves about 3/8 inch of the base visible near the door frame.
This configuration works well for most installations, partially positioning the doorbell over the adjacent brick and providing good door clearance.
This mount positions the doorbell over or in front of the brick face.
Standard Offset (This Product) vs Full Offset:
Need Maximum Sideways Clearance? Click here for the Full Offset version for these models.
Base Dimensions & Mounting: The extension base is 9/16 inches wide (requires >= 9/16" surface). Standard mounting hole spacing is 2.5 inches (center-to-center). Ensure solid mounting on trim. Wall-mounting screws not included.
Angled Trim? If your trim is angled, add our Angle Shims (sold separately) for a perpendicular installation.
CRITICAL: Measure & Select Your Extension Length!
Choose the correct length to clear your brickwork or storm door. Measure carefully:
- Measure the exact distance straight out from the surface where the mount base will attach (your trim) to the outermost face of your brick or obstacle.
- Order THIS measurement as your required Extension Length. (Do NOT subtract doorbell thickness for offset mounts).
Select the required extension length from the dropdown menu when ordering. (Starts at 1/4 inch).
Need help measuring? Text/email a picture! (Contact info below)
Measure like this from Trim to Brick Face for Extension Length.
Key Features & Benefits:
- Fits Ring Battery Doorbell Plus (and models 2, 3, 3+, 4 with removable batteries).
- Standard 5/8" Offset: Provides good sideways positioning for most common needs.
- "Over Brick" Placement: Extends doorbell forward past brick, positioning it partially over the brick face.
- Avoid Drilling Brick: Mounts to existing trim (>=9/16" wide, Std. 2.5" hole spacing).
- Selectable Extension Length: Order the precise depth needed (Trim-to-Brick/Obstacle measurement).
- Narrow Base (9/16" Std): Fits most standard trim widths.
- Wire Passthrough: Internal channel accommodates optional hardwiring.
- Durable PETG Construction: Strong, weather-resistant plastic.
- Add-on Compatible: Works with angle shims, fillers etc. (see below).
- Future-Proof Bracket: Top adapter bracket is replaceable for future upgrades (available here).
How to Install Your Standard Offset Extension
This mount uses two main printed pieces: the Extension Base and the Doorbell Adapter Bracket.
-
Tools & Prep: Gather: Drill, PH1 & PH2 Philips Screwdrivers/Bits, Level, Anchors (if needed), Ring security screwdriver (often orange, from doorbell box).
Turn OFF power at the breaker if hardwiring! Ensure battery is charged but removed during install.
-
Mount Extension Base: Position the Extension Base (correct length/offset) on trim over wires. Attach securely using appropriate screws (#6 size likely, use PH2) and anchors into the 2.5" spaced holes.
Ensure base is level. Don't overtighten.
-
Attach Doorbell Adapter Bracket: Route wires through the Doorbell Adapter Bracket. Align onto Extension Base. Attach using the four small center screws provided (likely #4 screws / PH1 driver).
Use correct PH1 bit. Tighten until flush. Check for/clear debris if needed. Do NOT over-torque.
- Wire Doorbell (If Hardwiring): Connect wires to your Ring Doorbell following Ring's instructions. Tuck excess wire.
-
Attach Ring Doorbell:
- Take the main body of your Ring Doorbell (with battery removed, faceplate off).
- Align the mounting holes on the back of the doorbell body with the holes on the Doorbell Adapter Bracket.
- Secure the **doorbell body** to the Adapter Bracket using the small screws PROVIDED WITH THIS MOUNT (typically #4 / PH1 driver). Do NOT use Ring's longer wall screws here.
- Re-install the battery (if not hardwired) and snap the Ring faceplate back on. Secure with Ring's security screw(s) at the bottom using the Ring screwdriver.
Use correct drivers/tools for each screw type. Tighten gently. - Final Check & Power On: Ensure doorbell is secure. Turn power back on (if applicable) and test.
Follow safety rules & Ring's guidelines. Use correct anchors/screws for wall type. Correct screwdriver size prevents stripping.
Optimal Placement for Your Doorbell Plus
The Ring Battery Doorbell Plus Brick Extension Mount is designed specifically to enhance the placement of your doorbell. It features a 9/16-inch wide design that fits securely onto most surfaces >= 9/16" wide. This mount provides a standard offset of 5/8 inches, which makes it easier for guests to see and use your doorbell, while providing good clearance for many installations.
Durability and Reliability
This brick extension mount is functional and durable. Made from weather-resistant PETG, it withstands different conditions while ensuring your Doorbell Plus remains secure. It allows your Doorbell Plus to remain accessible and visible, giving your entryway a smart boost.
Easy Installation Process
Installing the Ring Battery Doorbell Plus Brick Extension Mount is straightforward using your existing trim. It includes necessary hardware (assembly screws) and instructions so you can set it up without needing professional help, enhancing your home security effortlessly.
Optional Add-ons & Accessories:
Further customize your installation:
-
Angle Shims (5°, 10°, 15°)Corrects for angled trim *under the Extension Base*.
-
Horizontal Angle Adapter or Swivel Add-onAdd horizontal angle adjustment to the end of the extension.
-
Bottom Filler Spacer PlateFills the gap below the extension base on angled/uneven trim.
-
Body Shim Filler PlateFills gaps between the extension body and uneven brick.
-
Add Side Wire EntryAdds side entry holes ("mouse holes") to the *Extension Base* (add service to cart).
Product Examples
(See listing photos for details or contact us for more examples!)
Need Help? Confirm Compatibility & Measurements!
Ensure you have a compatible Ring Removable Battery model (Plus, 2, 3, 3+, 4). Need help measuring extension length?
- Email: shop@doorbellmount.com (Send Pictures!)
- Text/Call: 1-833-326-6868 (Text Pictures!)
Standard Color: Black. For other colors, add the Color Change Request item.
Doorbell Not Included. Includes the 2-piece extension mount (Extension Base + Doorbell Adapter Bracket) and necessary assembly screws.
PETG Material: Printed in durable, outdoor-rated PETG.
3D Printed Quality: Minor cosmetic variations inherent to 3D printing may exist but do not affect function. Contact us with quality concerns before reviewing.
Order the Standard Offset Brick Extension for your Ring Battery Doorbell Plus (or 2/3/4) today! Remember to measure carefully (Trim to Brick Face!) and select your required extension length.
