Eufy Doorbell Centered Brick Face Extension Mount (Flush Fit)
Compatibility: Eufy Doorbells & Trim Width
-
Fits Eufy Models Including:
- Eufy S330 (Dual Cam)
- Eufy E340 (Dual Cam)
- Eufy S220 / C210 (Single Cam - Wired/Wireless versions)
- (Leave a note with your specific model for potential bracket optimization)
- WILL NOT FIT: Doorbells from other brands (Ring, Nest, etc.).
- Surface Width: Requires mounting surface (trim/molding) to be AT LEAST 9/16 inches wide for the base.
Please double-check your Eufy model before ordering!
Position Your Eufy Doorbell Flush with Brick!
Is your Eufy Doorbell mounting spot recessed behind brick or stone? This **Centered Brick Face Extension Mount** is designed to bring your doorbell forward, aiming to position the **front face** of the doorbell approximately **flush with your brick surface** for the cleanest possible installation.
It features a **narrow 9/16-inch wide base** suitable for most trim and extends straight out (centered, no offset) by the length you select based on your measurements. Mounts directly to your trim, avoiding drilling into masonry.
How it Works: Centered Extension for "Face Flush"
This mount provides a STRAIGHT, CENTERED extension (no sideways offset). It's designed to bring the doorbell mounting point forward from recessed trim.
The goal with the recommended measurement (see guide below) is to have the **FRONT FACE of your Eufy Doorbell** sit approximately **FLUSH** with the outer surface of your brickwork. This provides a sleek, integrated look.
If you need sideways offset for door clearance, see our "Offset Brick Extension" listings for Eufy.
Base Dimensions & Mounting: This extension base is 9/16 inches wide (requires >= 9/16" surface). Standard mounting hole spacing is 2.5 inches (center-to-center). Ensure solid mounting on trim. Wall-mounting screws not included.
Angled Trim? If your trim is angled, add our Angle Shims (sold separately) for a perpendicular installation.
CRITICAL: Measure for Extension Length (Face Flush Goal)!
Choosing the correct extension length is essential to position the front face of your doorbell approximately flush with your brick face. Please measure carefully:
-
Method 1 (Most Accurate - If you HAVE doorbell):
- Temporarily hold your Eufy doorbell so its FRONT FACE level/flush with the outer face of the brick.
- Measure the distance straight back from the surface where the mount base will attach (your trim) to the flat mounting surface on the BACK of your doorbell.
- Order THIS measurement as your required Extension Length.
-
Method 2 (Estimate - If NO doorbell):
- Measure distance straight out from trim surface to outer brick face.
- Subtract approx. **1 inch to 1.25 inches** (typical Eufy doorbell thickness). Order this calculated length.
(Example: If Trim-to-Brick is 3 inches, and doorbell is ~1.25" thick, order ~1.75" extension. Our bracket uses ~1/2" internal space, so this gets close.)
(Note: Result may be slightly proud/recessed. Method 1 preferred.)
Select the required extension length from the dropdown menu when ordering.
Need help measuring? Text/email a picture! (Contact info below)
Use measurement method described above. Diagram shows general concept.
Key Features & Benefits:
- Fits Eufy Doorbells: Compatible with S330, E340, S220, C210 models (Wired/Wireless Single Cam).
- Centered Design: Extends doorbell straight forward without sideways offset.
- "Face Flush" Goal: Aims to align doorbell front face with the brick surface plane.
- Avoid Drilling Brick: Mounts to existing trim (>=9/16" wide, Std. 2.5" hole spacing).
- Selectable Extension Length: Order the precise depth based on your measurements for face-flush goal.
- Narrow 9/16" Base: Fits most standard trim widths.
- Wire Passthrough: Internal channel accommodates wiring.
- Durable PETG Construction: Strong, weather-resistant plastic for outdoor use.
- Direct Eufy Bracket Mount: Adapter plate is designed to accept the standard Eufy mounting bracket.
- Add-on Compatible: Works with angle shims, fillers etc.
- Future-Proof Bracket: Top adapter bracket potentially replaceable (check compatibility).
How to Install Your Centered Extension for Eufy
This mount uses two main printed pieces: the Extension Base and the Doorbell Adapter Bracket.
-
Tools & Prep: Gather: Drill, PH1 & PH2 Philips Bits, Level, Anchors (if needed), your Eufy doorbell backplate & hardware.
Turn OFF power at the breaker if hardwiring! Ensure doorbell is charged if battery version.
-
Mount Extension Base: Position the Extension Base (correct length, centered) on your >=9/16" trim over wires. Attach securely using appropriate screws (#6 size likely, use PH2) and anchors into the 2.5" spaced holes.
Ensure base is level. Don't overtighten.
-
Attach Doorbell Adapter Bracket: Route wires through the Doorbell Adapter Bracket (top piece for Eufy). Align onto Extension Base. Attach using the four small center screws provided (likely #4 screws / PH1 driver).
Use correct PH1 bit. Tighten until flush. Check for/clear debris if needed. Do NOT over-torque.
-
Attach Eufy Backplate: Secure the **backplate/wedge that came WITH your Eufy Doorbell** onto the Doorbell Adapter Bracket using the small screws PROVIDED WITH THIS MOUNT (typically #4 / PH1). Ensure correct orientation.
Do NOT use Eufy's long wall screws here. Use correct PH1 driver.
- Wire & Mount Eufy Doorbell: Connect wires (if applicable) to the Eufy backplate following Eufy's instructions. Click the Eufy Doorbell unit firmly onto its backplate until secure.
- Final Check & Power On: Ensure doorbell is secure. Turn power back on (if applicable) and test.
Follow safety rules & Eufy guidelines. Use correct anchors/screws. Correct screwdriver size prevents stripping.
Enhance Your Eufy Doorbell Installation
Perfect Fit for Brick Surfaces
The Eufy Doorbell Brick Extension is specifically designed for homes with brick adjacent to trim. Its 9/16 inch wide base ensures a sturdy installation, allowing your Eufy Doorbell (Single or Dual Cam models) to function optimally and integrate cleanly.
No Offset for a Clean Look
This mount positions your doorbell straight forward without sideways offset, creating a refined appearance that enhances curb appeal. It ensures the doorbell is accessible and visible while maintaining clean lines.
Weather Resistant & Durable Construction
Made from high-quality PETG, this extension withstands outdoor conditions like rain, snow, and sun. This durability ensures your doorbell remains protected and functional year-round, providing reliable home security.
Optional Add-ons & Accessories:
Further customize your installation:
-
Angle Shims (5°, 10°, 15°)Corrects for angled trim *under the Extension Base*.
-
Horizontal Angle Adapter or Swivel Add-onAdd horizontal angle adjustment to the end of the extension.
-
Bottom Filler Spacer PlateFills the gap below the extension base on angled/uneven trim.
-
Body Shim Filler PlateFills gaps between the extension body and uneven brick.
-
Add Side Wire EntryAdds side entry holes ("mouse holes") to the *Extension Base* (add service to cart).
-
Wire Extension Kit
Need longer wires? Purchase our extension wire kit with your choice of connectors.
Standard color is Black. For White, Brown, Grey, etc., add this service.
Product Examples
(See listing photos for details or contact us for more examples!)
Need Help? Confirm Compatibility & Measurements!
Ensure you have a compatible Eufy Doorbell model (S330, E340, S220, C210). Need help measuring for the "Face Flush" extension length?
- Email: shop@doorbellmount.com (Send Pictures!)
- Text/Call: 1-833-326-6868 (Text Pictures!)
Standard Color: Black. For other colors, add the Color Change Request item.
Doorbell Not Included. Includes the 2-piece extension mount (Extension Base + Doorbell Adapter Bracket for Eufy) and necessary assembly screws.
PETG Material: Printed in durable, outdoor-rated PETG.
3D Printed Quality: Minor cosmetic variations inherent to 3D printing may exist but do not affect function. Contact us with quality concerns before reviewing.
Order the Centered Brick Face Extension for your Eufy Doorbell today! Remember to measure carefully for the Face Flush goal and select your required extension length.
