15-90° Swivel Mount for SkyBell HD (Round Body) | Rotate the 180° View Toward Your Entry

$50.00
$40.00
Custom 15-90° Side-Wall Swivel Mount for the SkyBell HD Custom-Fit for the SkyBell HD Custom-shaped for the SkyBell HD — the round SkyBell HD / legacy Alarm.com-compatible doorbell body. Not a universal one-size mount: other doorbell brands use different body...
Availability: Many In Stock
Product Type: Adjustable Mount 15-90°

Custom 15-90° Side-Wall Swivel Mount for the SkyBell HD

Custom-Fit for the SkyBell HD

  • Custom-shaped for the SkyBell HD — the round SkyBell HD / legacy Alarm.com-compatible doorbell body.
  • Not a universal one-size mount: other doorbell brands use different body shapes and each has its own listing on our store.
  • Switching doorbells later? The base stays on the wall — grab a ~$10 Replacement Bracket for the new model.
Don't have the doorbell yet? Get the SkyBell HD on Amazon →

Point the Camera at Your Doorstep, Not the Siding

The SkyBell HD's round 180° lens covers the whole porch, but on a side wall the stock plate aims it at the wall instead of your visitor.

This adjustable 15-90° adjustable side-wall swivel mount swings the SkyBell HD outward across a wide 15° to 90° arc so the 1080p 180° view lands on your visitor and the doorstep instead of the wall. Set screws lock the angle so it will not drift after the first windstorm or cold snap.

15° to 90° of Adjustable Aim

Built for real angle correction, the adjustable side-wall swivel lets you aim across a 15° to 90° arc relative to the wall — it shines above 45°. Adjust left/right and up/down, then tighten the set screws to lock it.

15-90 degree side-wall swivel adjustability diagram for SkyBell HD Video Doorbell (2017)
15° to 90° of dual-axis aim for perpendicular-wall installs.

Only need a small nudge (<15°) or a straight-ahead view? See our 0-35° Swivel Mount for the SkyBell HD instead.

Hidden Wire Pass-Through

If the doorbell is hardwired (10-36V AC), the wires come out of the wall, pass through the concealed channel in the swivel, run through the front SkyBell HD bracket, and land on the doorbell terminals — nothing exposed at the joint.

Concealed wire routing for the 15-90 degree swivel mount and SkyBell HD Video Doorbell (2017)

Size & Weight

  • Base Width: 1.8 in
  • Base Height: 3.1 in
  • Base Hole Spacing: 2-5/8 in (center-to-center)
  • Reach at 15°: ~2.0 in
  • Reach at 90°: ~3.5 in
  • Weight: ~2 oz (mount only)
  • Standard 1.8" base; a narrow 3/4" baseplate is available — see Customization.

Why This Mount Works

  • Custom Bracket for the SkyBell HD: A pre-shaped pocket cradles the body without blocking the lens, mic, or field of view.
  • Hidden Wire Pass-Through: An internal channel routes the low-voltage leads cleanly to the doorbell terminals.
  • Locking Set Screws: Set the angle once and it stays put — no drift in cold weather or after a firmware update.
  • Siding Compatible: Sits flat on flat surfaces or lapped siding up to 1.8 inches wide.
  • Complete Kit: Adjustable base, custom SkyBell HD bracket, and all the mounting screws you need.
  • UV-Stable PETG: Freeze-tolerant, weatherproof 3D-printed PETG made for year-round outdoor use.
  • Reusable Base: Switch doorbell brands later and just order a ~$10 Replacement Bracket — the base stays on the wall.

Customize It

Installing It on the SkyBell HD

  1. Power first. Kill power to the doorbell circuit at the breaker before you touch the wires.
    If hardwiring, confirm power is off with a multimeter before stripping wires.
  2. Grab your tools. Drill, PH2 (#6 wall screws), PH1 (#4 bracket/set/doorbell screws), a level, and anchors if you're not hitting a stud.
  3. Pick the angle before drilling. Stand where a visitor stands, picture the line from the doorbell to that spot, and rough in that angle so you don't re-drill.
  4. Mount the base. Line it up with your siding or trim and drive the #6 screws (PH2).
    Pilot-drill if needed and don't overtighten.
  5. Add the swivel. Feed the wires through the center (skip if battery) and fasten the swivel to the base with the four #4 / PH1 screws.
  6. Rough-set the aim. Turn it toward the walkway inside the 15-90° range and snug one or two set screws for now.
  7. Attach the SkyBell HD. Snap it on with the screws included with this mount (PH1). Do not reuse the stock back plate — our bracket replaces it.
  8. Confirm in the SkyBell / Alarm.com app, then lock. Power up, open Live View, check the framing, and tighten all set screws hand-tight.
    Snug is enough — don't crank the set screws.
  9. Redraw detection zones. In the SkyBell / Alarm.com app, tighten the motion zones to the new framing so you exclude the street and the neighbor's yard.

Common Questions

Will this 15-90° mount fit my SkyBell HD?
Yes — this bracket is cut to the SkyBell HD body, so the doorbell drops into a model-specific pocket with the lens and mic clear. It does not fit other brands; each has its own listing.
How fast does it ship?
Each mount is printed to order and typically ships within 2-3 business days from our USA shop.
What's the difference between the 15-90° and 0-35° mount?
The 15-90° version is for big side-wall corrections — when the doorbell sits on a perpendicular wall, pillar, or outside corner. The 0-35° version is for fine-tuning aim on a flat wall. If you need more than about 15° of turn, pick this one.
Can I use this on vinyl siding, Hardie board, or stucco?
Yes. The 1.8" base sits flat on most lapped siding. For vinyl siding without drilling the siding itself, add our Vinyl Siding Adapter; for fiber-cement, use our Hardie Siding Mount; for stucco, drill pilot holes and use masonry anchors.
What hardware is included?
You get the adjustable swivel base, the custom adapter bracket, locking set screws, mounting screws (#6 PH2 for the wall and #4 PH1 for the bracket and doorbell), and wall anchors. Use only the screws provided, not the doorbell's stock backplate screws.

✔ Replacement Guarantee — The Right Part, Guaranteed

Send a photo of your install spot and doorbell BEFORE you order and we'll point you to the exact part. If you order and it doesn't fit, we'll send the correct one at NO additional cost.

  • Before ordering: text or email photos of (1) the install location and (2) the doorbell; we'll confirm the fit.
  • If it doesn't fit: send a photo of the doorbell and the fit problem — we ship the correct part free.
  • Reach us: 833-326-6868 / shop@doorbellmount.com.

Need the Doorbell?

Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases at no extra cost to you.

Questions?

Standard Color: Black. Other colors via the Color Change Request.

Angle Note: "15-90°" is the approximate range for perpendicular installs; actual angle depends on positioning.

3D-Printed: minor layer lines may show and do not affect strength or weather resistance.

Get the right side-wall angle on your SkyBell HD — order today and we'll print and ship within 2-3 business days.