Adjustable Mount
90° Adjustable Swivel Mount | 3/4in Wide Base Adapter Included | Slim Tight Spot Fitting
90° Adjustable Swivel Mount | 3/4in Wide Base Adapter Included | Slim Tight Spot Fitting
Narrow 3/4in Wide Base and Adjustable Swivel Doorbell Mount
Couldn't load pickup availability
Slim Trim Doorbell Mount (3/4" Base) with 90° Swivel Adjustment | Select Model
Narrow Base Fit & Model Selection Required!
This articulating mount includes our **Ultra-Slim 3/4" Base Plate**, specifically designed for installation on narrow door frames or trim (requires a minimum surface width of 3/4 inch).
- CRITICAL: You MUST Select Your Specific Doorbell Model from the options list to receive the correct custom-fitted adapter bracket.
- Supports most major video doorbell brands (Ring, Nest, Eufy, Wyze, etc.).
- Uncertain About Your Doorbell? Brand names can be confusing! Please contact us with a photo before ordering if you're unsure.
- Need a Different Model? We frequently add support for new doorbells and offer custom designs.
For assistance identifying Ring models, consult our Ring Model Guide.
Extreme Angle Correction for Narrow Spaces!
Dealing with an awkward mounting spot? This **15-90° Adjustable Swivel Mount** provides unprecedented aiming control, allowing you to turn your doorbell up to 90 degrees relative to the wall. Combined with its **ultra-slim 3/4-inch wide base**, it's the ultimate problem-solver for mounting on narrow door frames or posts while achieving a perpendicular side view.
Correct challenging angles, overcome obstructions, and ensure your camera covers the critical approach path, even from the tightest installation locations.
Full Range Motion: 15-90° Pan & Tilt Freedom
Achieve superior surveillance coverage with extensive adjustment capabilities. This mount's robust joint offers a **15-to-90-degree range of motion** both **horizontally and vertically**, allowing you to precisely direct your doorbell's camera lens.
Flexible Base Orientation: The narrow 3/4" base can be oriented with screw holes vertically or horizontally, offering adaptability for different mounting surfaces while keeping the doorbell properly upright.
Physical Specifications (Narrow Base Model)
- Mounting Base Width: 3/4 inches (0.75") - Installs on surfaces >= 3/4" wide.
- Mounting Base Length: Approx. 2.5 inches.
- Mounting Hole Spacing (Base): Typically 2 inches center-to-center (confirm if specific spacing needed).
- Swivel Range: Approx. 15° to 90° (Dual Axis).
- Protrusion: Varies with angle; includes neck for clearance at wider angles.
Mounting Kit Highlights:
- Ultra-Slim 3/4" Base: Tailor-made for narrow door frames and minimal surface areas.
- Maximum Angle Flexibility (15-90°): Wide-range dual-axis swivel for extreme horizontal/vertical positioning.
- Corner & Side Wall Solution: Perfect for aiming camera around corners or from perpendicular walls.
- Customized Adapter Bracket: Select your doorbell model for a guaranteed secure fit.
- Solid Angle Locking: Set screws maintain the desired viewing angle reliably.
- Adaptable Base Install: Mount base plate vertically or horizontally as needed.
- Integrated Wire Channel: Allows for clean pass-through of doorbell wires.
- All-Weather Durability: Constructed from resilient, outdoor-grade PETG plastic.
- Ready-to-Install Kit: Includes narrow base, swivel unit, custom adapter, and all necessary screws.
- Modular Bracket System: Base may support different adapter brackets for future doorbell changes (check options).
Setting Up Your Narrow Base Swivel Mount
-
Tools & Prep: Gather: Drill, PH1 & PH2 Philips Bits, Level, Anchors (if needed), doorbell & its specific hardware/tools.
Turn OFF power at the breaker if hardwiring!
-
Mount NARROW Base: Route wires through the **Narrow (3/4" Wide) Base Piece**. Position on your >=3/4" trim/wall (screws vertical or horizontal). Attach securely using appropriate screws (#6 size likely, use PH2) and anchors via the base's holes (typically 2" spacing).
Ensure base is level & secure. Avoid overtightening base screws.
-
Attach Swivel Bracket to Base: Route wires through the **Swivel Bracket**. Align onto Narrow Base & attach using four center screws provided (likely **#4 / PH1 driver**).
Use correct PH1 bit. Start gently. Do NOT over-torque.
- Set Initial Angle (15-90°): Adjust swivel bracket (up/down & left/right). Lightly tighten one/two **set screws** (likely #4 / PH1 driver).
- Wire Doorbell: Connect wires per manufacturer's instructions (if applicable). Tuck excess wire.
-
Attach Doorbell to Custom Bracket:
- Align your selected doorbell model (or its plate if used) with the pre-drilled holes on the custom swivel mount adapter bracket.
- Secure doorbell/plate using screws PROVIDED WITH THIS MOUNT (likely #4 / PH1 driver).
- DO NOT USE doorbell manufacturer's wall screws. Follow any final steps for your model (e.g., faceplate security screws).
Use correct drivers & provided screws. Tighten snugly. -
Finalize & Secure Angle: Make final adjustments. Fully tighten all **set screws** (likely PH1 driver) gently but firmly.
Do not overtighten set screws! Hand-tight is generally sufficient.Restore power (if applicable) and test.
Always follow safety protocols & your doorbell's specific guidelines. Use appropriate wall anchors. Using correct Philips bits prevents damage.
Overcome Installation Obstacles
Conquer Awkward Angles & Narrow Trim
Don't let challenging mounting locations compromise your security view. This mount's combination of an ultra-slim 3/4" base and an expansive 15-90° swivel range allows secure installation on narrow door frames while enabling extreme angle adjustments needed for side walls or corner views.
Achieve Comprehensive Coverage
Precisely aim your doorbell camera to monitor walkways, driveways, package drop zones, or any critical area. The dual-axis movement provides the control needed to eliminate blind spots and maximize the effectiveness of your video doorbell.
Protect Your Investment
Made from durable, weatherproof PETG plastic, this mount provides a stable, long-lasting platform designed to withstand outdoor elements, ensuring your video doorbell remains secure and functional for years to come.
Visual Guide & Product Examples
Example showing potential 90-degree angle use:
General installation concept video:
(Video demonstrates general swivel mount assembly.)
Need Assistance or Customization?
Confirming doorbell model compatibility is crucial! If unsure, or if your model isn't listed, please send photos before ordering. We also offer custom designs!
- Email: shop@doorbellmount.com (Include photos!)
- Text/Call: 1-833-326-6868 (Text photos!)
Color Info: Ships in Black by default. To request White or another color, please add the Color Change Request listing to your order.
Angle Range: Allows adjustment from approx. 15° up to 90° relative to the wall.
3D Printed Item: Made with durable PETG. Minor visual imperfections are normal for 3D printing and don't affect strength. Please contact us with quality concerns.
Kit Includes: Narrow base, 15-90° swivel assembly, model-specific top adapter bracket, installation hardware.
The perfect solution for narrow trim AND side walls! Order your Narrow Base 15-90° Swivel Mount now - don't forget to select your doorbell model!
