Arlo Essential Wired (AVD1001) Side-Wall Swivel Mount | 15° to 90° Adjustable Aim for Corner & Trim Installs

$50.00
$40.00
15-90° Perpendicular-Wall Mount for the Arlo Essential Wired (AVD1001) Custom-Fit for the Arlo Essential Wired (AVD1001) Custom-shaped for the Arlo Essential Wired (AVD1001) — Amazon ASIN B07YMV9VMT — the slim 1st-gen hardwired Arlo Essential body (screw terminals, no battery). Not...
Availability: Many In Stock
Product Type: Adjustable Mount 15-90°

15-90° Perpendicular-Wall Mount for the Arlo Essential Wired (AVD1001)

Custom-Fit for the Arlo Essential Wired (AVD1001)

  • Custom-shaped for the Arlo Essential Wired (AVD1001) — Amazon ASIN B07YMV9VMT — the slim 1st-gen hardwired Arlo Essential body (screw terminals, no battery).
  • Not a universal one-size mount: other doorbell brands use different body shapes and each has its own listing on our store.
  • Switching doorbells later? The base stays on the wall — grab a ~$10 Replacement Bracket for the new model.
Don't have the doorbell yet? Get the Arlo Essential Wired (AVD1001) on Amazon →

Aim It Where Visitors Actually Stand

The Arlo Essential Wired's 1:1 180° head-to-toe lens has to face the doorstep. On a side wall, the flat factory plate points it at the wall.

This adjustable 15-90° perpendicular-wall pivot mount swings the Arlo Essential Wired (AVD1001) outward across a wide 15° to 90° arc so the 1:1 180° head-to-toe view lands on your visitor and the doorstep instead of the wall. Set screws lock the angle so it will not drift after the first windstorm or cold snap.

Adjustable Side-Wall Angle, Locked in Place

Built for real angle correction, the perpendicular-wall pivot lets you aim across a 15° to 90° arc relative to the wall — it shines above 45°. Adjust left/right and up/down, then tighten the set screws to lock it.

15-90 degree side-wall swivel adjustability diagram for Arlo Essential Wired Video Doorbell (AVD1001, 2020)
15° to 90° of dual-axis aim for perpendicular-wall installs.

Only need a small nudge (<15°) or a straight-ahead view? See our 0-35° Swivel Mount for the Arlo Essential Wired (AVD1001) instead.

Wires Stay Tucked Inside the Swivel

If the doorbell is hardwired (16-24V AC), the wires come out of the wall, pass through the concealed channel in the swivel, run through the front Arlo Essential Wired (AVD1001) bracket, and land on the doorbell terminals — nothing exposed at the joint.

Concealed wire routing for the 15-90 degree swivel mount and Arlo Essential Wired Video Doorbell (AVD1001, 2020)

Footprint & Weight

  • Base Width: 1.8 in
  • Base Height: 3.1 in
  • Base Hole Spacing: 2-5/8 in (center-to-center)
  • Reach at 15°: ~2.0 in
  • Reach at 90°: ~3.5 in
  • Weight: ~2 oz (mount only)
  • Standard 1.8" base; a narrow 3/4" baseplate is available — see Customization.

Built for the Job

  • Custom Bracket for the Arlo Essential Wired (AVD1001): A pre-shaped pocket cradles the body without blocking the lens, mic, or field of view.
  • Siding Compatible: Sits flat on flat surfaces or lapped siding up to 1.8 inches wide.
  • Complete Kit: Adjustable base, custom Arlo Essential Wired (AVD1001) bracket, and all the mounting screws you need.
  • UV-Stable PETG: Freeze-tolerant, weatherproof 3D-printed PETG made for year-round outdoor use.
  • Reusable Base: Switch doorbell brands later and just order a ~$10 Replacement Bracket — the base stays on the wall.
  • Made in the USA: Printed and shipped from our own shop, not mass-produced overseas.
  • Corner & Trim Friendly: Reaches past narrow trim and outside corners where the flat stock plate can't aim.

Customize It

Installing It on the Arlo Essential Wired (AVD1001)

  1. Power first. Kill power to the doorbell circuit at the breaker before you touch the wires.
    If hardwiring, confirm power is off with a multimeter before stripping wires.
  2. Grab your tools. Drill, PH2 (#6 wall screws), PH1 (#4 bracket/set/doorbell screws), a level, and anchors if you're not hitting a stud.
  3. Pick the angle before drilling. Stand where a visitor stands, picture the line from the doorbell to that spot, and rough in that angle so you don't re-drill.
  4. Mount the base. Line it up with your siding or trim and drive the #6 screws (PH2).
    Pilot-drill if needed and don't overtighten.
  5. Add the swivel. Feed the wires through the center (skip if battery) and fasten the swivel to the base with the four #4 / PH1 screws.
  6. Rough-set the aim. Turn it toward the walkway inside the 15-90° range and snug one or two set screws for now.
  7. Attach the Arlo Essential Wired (AVD1001). Snap it on with the screws included with this mount (PH1). Do not reuse the stock back plate — our bracket replaces it.
  8. Confirm in the Arlo Secure app, then lock. Power up, open Live View, check the framing, and tighten all set screws hand-tight.
    Snug is enough — don't crank the set screws.
  9. Redraw detection zones. In the Arlo Secure app, tighten the motion zones to the new framing so you exclude the street and the neighbor's yard.

Before You Order

How do I know this fits my Arlo Essential Wired (AVD1001)?
Yes — this bracket is cut to the Arlo Essential Wired (AVD1001) body, so the doorbell drops into a model-specific pocket with the lens and mic clear. It does not fit other brands; each has its own listing.
How fast does it ship?
Each mount is printed to order and typically ships within 2-3 business days from our USA shop.
What's the difference between the 15-90° and 0-35° mount?
The 15-90° version is for big side-wall corrections — when the doorbell sits on a perpendicular wall, pillar, or outside corner. The 0-35° version is for fine-tuning aim on a flat wall. If you need more than about 15° of turn, pick this one.
Can I use this on vinyl siding, Hardie board, or stucco?
Yes. The 1.8" base sits flat on most lapped siding. For vinyl siding without drilling the siding itself, add our Vinyl Siding Adapter; for fiber-cement, use our Hardie Siding Mount; for stucco, drill pilot holes and use masonry anchors.
What hardware is included?
You get the adjustable swivel base, the custom adapter bracket, locking set screws, mounting screws (#6 PH2 for the wall and #4 PH1 for the bracket and doorbell), and wall anchors. Use only the screws provided, not the doorbell's stock backplate screws.

✔ Replacement Guarantee — The Right Part, Guaranteed

Send a photo of your install spot and doorbell BEFORE you order and we'll point you to the exact part. If you order and it doesn't fit, we'll send the correct one at NO additional cost.

  • Before ordering: text or email photos of (1) the install location and (2) the doorbell; we'll confirm the fit.
  • If it doesn't fit: send a photo of the doorbell and the fit problem — we ship the correct part free.
  • Reach us: 833-326-6868 / shop@doorbellmount.com.

Need the Doorbell?

Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases at no extra cost to you.

Questions?

Standard Color: Black. Other colors via the Color Change Request.

Angle Note: "15-90°" is the approximate range for perpendicular installs; actual angle depends on positioning.

3D-Printed: minor layer lines may show and do not affect strength or weather resistance.

Turn your Arlo Essential Wired (AVD1001) toward your visitors — printed to order, ships within 2-3 business days.