15-90° Adjustable Swivel Mount for Ring Battery Doorbell (2nd Gen, 2026) | Retinal 2K | Wide-Angle Tilt & Pivot

$50.00
$40.00
15-90° Adjustable Side-Wall Mount for the Ring Battery Doorbell (2nd Gen, 2026) — Retinal 2K Custom-Fit for the Ring Battery Doorbell 2nd Gen — Retinal 2K This bracket is shaped specifically for the Ring Battery Doorbell (2nd Gen, 2026) —...
Availability: Many In Stock
Product Type: Adjustable Mount 15-90°

15-90° Adjustable Side-Wall Mount for the Ring Battery Doorbell (2nd Gen, 2026) — Retinal 2K

Custom-Fit for the Ring Battery Doorbell 2nd Gen — Retinal 2K

  • This bracket is shaped specifically for the Ring Battery Doorbell (2nd Gen, 2026) — Amazon ASIN B0G2D1R15Q. Ring's refreshed entry battery doorbell with Retinal 2K vision and integrated rechargeable battery (no quick-release).
  • Does NOT fit: the Ring Battery Plus 2nd Gen, the Battery Pro 2nd Gen, any older Ring battery doorbell (Ring 2, 3, 3+, 4, original), or any wired Ring doorbell. Each Ring doorbell has its own dedicated mount listing on our store.
  • Not sure which Ring you have? Send a photo of the back of your doorbell to shop@doorbellmount.com or text us — we'll confirm fit before you order.
Don't have the doorbell yet? Get the Ring Battery Doorbell 2nd Gen on Amazon →

Need help identifying a Ring model? Check our Ring Model Guide or our Best Ring Doorbells 2025 Guide.

Battery Doorbell, Side-Wall Aim, Permanent Lock

Battery doorbells are wonderful — until you put one on a side wall and realize the head-to-toe lens just framed your siding. This Adjustable 15-90° Swivel Mount is the answer for the new Ring Battery Doorbell 2nd Gen: a custom-fit pocket bracket on a bent-neck dual-axis pivot, with a wide 15° to 90° arc for proper side-wall geometry.

Because the Ring Battery 2nd Gen has no wall-side connector, all you need on the wall is a clean, locked, weather-tight bracket. This mount delivers exactly that — and the angle stays put when you pop the doorbell off to charge.

Wide Dual-Axis Control (15-90°) — Built for the Retinal 2K Lens

Designed for significant angle correction, this mount features a unique bent-neck swivel joint. Precise aiming control across a 15° to 90° arc relative to the wall — ideal for side-facing views (excels at angles greater than 45°). Fine-tuning is possible both horizontally (left/right) and vertically (up/down). Once the angle is set, the locking set screws hold position permanently — critical for Retinal 2K sharpness on any side-wall install.

15-90 degree side-wall swivel mount adjustability diagram for Ring Battery Doorbell 2nd Gen
15° to 90° pivot — dual-axis swivel for perpendicular-wall installs.

Note: this design is optimized for substantial side angles. If you only need a very minor (<15°) adjustment or a straight-ahead view, see our 0-35° Swivel Mount for the Ring Battery Doorbell 2nd Gen instead.

Internal Wire Routing — Hidden & Protected

Doorbell wiring (or PoE cable, where applicable) enters from the wall, passes through the hidden internal channel inside the swivel joint, routes through the front Ring Battery Doorbell 2nd Gen adapter bracket, and connects directly to the doorbell terminals. No exposed wiring, no weather risk — even at extreme 90° angles.

Internal wire routing diagram — wires pass cleanly through the 15-90 degree swivel mount and connect to the Ring Battery Doorbell 2nd Gen terminals

Mount Dimensions & Weight

  • Base Width: 1.8 inches
  • Base Height: 3.1 inches
  • Base Hole Spacing: 2-5/8 inches (center-to-center)
  • Wall Extension at 15°: ~2.0 inches
  • Wall Extension at 90°: ~3.5 inches (extends doorbell perpendicular to wall)
  • Weight: ~2 oz (PETG mount only)
  • (Note: This is the standard 1.8" base; narrow 3/4" baseplate option available — see Customization section.)

Key Features & Benefits

  • Wide Adjustable Angle (15-90°): Significant dual-axis swivel built specifically for side-wall / perpendicular installations.
  • Custom-Fit Bracket for Ring Battery Doorbell 2nd Gen: Charge-friendly geometry — bracket clearance lets you pop the doorbell off without removing it from the wall.
  • Secure Locking Set Screws: Once you set the angle, it stays. No drift in cold weather, no need to readjust after firmware updates.
  • Wire Pass-Through: Hole in the swivel joint routes the doorbell's power cable neatly — no exposed wiring at the joint.
  • Siding Compatible: Flat surfaces or lapped siding up to 1.8 inches wide.
  • Complete Kit: Adjustable base, custom Ring Battery Doorbell 2nd Gen bracket, and all necessary mounting screws.
  • Durable PETG: Sturdy 3D-printed PETG, UV-stable and freeze-tolerant for outdoor use.
  • Side-Wall Problem Solver: Eliminates the "side wall view" issue for proper security coverage of the porch.
  • Future-Proof Base: Base is compatible with future Ring doorbell adapter brackets — when Ring releases the next generation, just swap the small ~$10 adapter. Find replacement brackets here.

Customization & Add-On Options

We offer solutions for almost any mounting situation:

Installing Your 15-90° Side-Wall Mount on the Ring Battery Doorbell 2nd Gen

  1. Tools & Prep: Gather a drill, PH2 Philips (#6 base screws), PH1 Philips (#4 bracket/set/doorbell screws provided), wall anchors if needed, level, and a multimeter.
    Battery-powered — no transformer required. Optional trickle-charge wiring (8-24V AC) supported via the back terminals if your install has existing doorbell wires.
  2. Plan the Aim Angle BEFORE Drilling: Stand where a visitor would stand. Visualize the angle from the doorbell location to that spot. 15-90° gives you a wide range — but committing to roughly the right angle before drilling pilot holes saves rework.
  3. Mount the Base: Route any existing doorbell wires through the base hole. Position vertical and attach using #6 screws (PH2 driver) with anchors as needed.
    Drill pilot holes if needed. Don't overtighten base screws.
  4. Attach the Swivel Bracket: Route wires through the swivel joint. Align onto the base and attach using four center screws (#4 / PH1 driver).
  5. Set Initial Angle: Adjust the swivel within 15-90° toward the visitor approach. Lightly tighten one or two set screws (#4 / PH1 driver) — final tightening comes after Live View confirmation.
  6. Wire the Ring Battery Doorbell 2nd Gen (or seat the battery): If hardwired, connect the two leads to the doorbell screw terminals — polarity doesn't matter for AC. If battery-only, you'll seat the battery at step 8.
  7. Attach the Doorbell to the Bracket: Align the Ring Battery Doorbell 2nd Gen with the pre-drilled holes on the custom Ring Battery Doorbell 2nd Gen-specific bracket. Secure using the screws PROVIDED WITH THIS MOUNT (#4 / PH1 driver). DO NOT USE the screws or wedge plate that came with your Ring doorbell.
    Tighten snugly, do not overtighten. Use the correct PH1 driver for provided screws.
  8. Aim Using Live View & Finalize Set Screws: Restore power (or insert the battery). Open the Ring app → Live View. With the Retinal 2K head-to-toe lens, you'll see if the side-wall framing is right. Adjust the 15-90° swivel and lock the set screws.
    Do not overtighten set screws — hand-tight is sufficient. Over-tightening can crack the swivel joint.
  9. Tune Smart Notifications + Motion Zones: In the Ring app, redraw motion zones to match the new angle. Side-wall installs benefit from a tighter "porch path" zone — the wider 90° angle catches more peripheral motion (cars passing, mail truck) that you'll want to exclude.

Side-wall tip: extreme 90° angles slightly increase wind load on the doorbell. The set-screw lock is rated for it, but on installs in high-wind regions (coastal, exposed corners), the bracket's wider extension at 90° puts slight pre-loaded weight on the joint — completely fine, just normal for side-wall geometry.

FAQ — Ring Battery Doorbell 2nd Gen 15-90° Mount

Will this 15-90° mount fit the Ring Battery Doorbell 2nd Gen (2026)?
Yes. The bracket is custom-shaped for the Ring Battery Doorbell 2nd Gen (2026), Amazon ASIN B0G2D1R15Q. It will NOT fit the Ring Battery Plus 2nd Gen, the Battery Pro 2nd Gen, or any older Ring battery doorbell (Ring 2, 3, 3+, 4, original Battery Doorbell).
Does the integrated battery affect the mount design?
Yes — the bracket is designed with charging in mind. The Ring Battery 2nd Gen has an integrated (non-removable) battery that's charged via USB. The bracket geometry lets you pop the doorbell off the mount for charging without removing the mount itself, then snap it back in the same aim position.
Can I hardwire the Battery 2nd Gen for trickle-charging?
Yes. If your install has existing 8-24V AC doorbell wiring, you can connect the leads to the back terminals on the doorbell for continuous trickle-charge. Polarity doesn't matter for AC. The mount routes those wires through the internal channel.
How is this different from the 0-35° Battery 2nd Gen mount?
The 15-90° version is for side-wall, corner, or perpendicular installs where you need to swing the camera outward by 30° or more. The 0-35° version is for flat-wall installs where the camera faces the visitor already and you only need fine-tune aim correction.
Will the side-wall angle drain the battery faster?
No. Battery life depends on how often the camera wakes for motion or rings — the angle doesn't change that. However, side-wall installs often catch more peripheral motion (cars, mail trucks). After install, tighten the motion zones in the Ring app to focus on the porch path so battery life stays in the expected 6-month range.
Will I lose any features (HDR, head-to-toe, Smart Notifications) by using this mount?
No. The mount is purely mechanical — all Retinal 2K, head-to-toe, Smart Notifications, and Quick Replies features work exactly as they do on the factory wedge.
How weatherproof is the 3D-printed PETG?
Very. UV-stable PETG, freeze-tolerant, and tested across full year-round outdoor cycles. Real-world installs are 4+ years without degradation. Ring's standard wedge is also plastic — same outdoor expectation.

Installation Video & Examples

Example 90 degree side wall doorbell installation Adjustable base component for side-wall doorbell mount
Watch: Swivel Doorbell Installation Video

(Video shows general installation principles for our swivel mounts.)

Need to Buy the Doorbell or Accessories?

Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases at no extra cost to you.

Questions? Need Help?

We're here to help! If you're unsure about your Ring model or need a custom solution for your 90-degree install:

Standard Color: Ships in Black. For other colors, use the Color Change Request.

Angle Note: The term "15-90°" represents the approximate adjustment range for perpendicular installations. Actual achievable angle depends on positioning.

3D-Printed Parts: Minor cosmetic variations or layer lines may be present and do not affect strength or weather resistance.

Order your Adjustable 15-90° Side-Wall Mount for the Ring Battery Doorbell 2nd Gen today — finally get the right view from your side-mounted doorbell.