15-90° Adjustable Swivel Mount for Ring Wired Doorbell (2nd Gen, 2026) | Retinal 2K | Side-Wall Aim & Lock

$50.00
$40.00
Adjustable 15-90° Side-Wall Mount for the Ring Wired Doorbell (2nd Gen, 2026) — Retinal 2K Custom-Fit for the Ring Wired Doorbell 2nd Gen — Retinal 2K This bracket is shaped specifically for the Ring Wired Doorbell (2nd Gen, 2026) —...
Availability: Many In Stock
Product Type: Adjustable Mount 15-90°

Adjustable 15-90° Side-Wall Mount for the Ring Wired Doorbell (2nd Gen, 2026) — Retinal 2K

Custom-Fit for the Ring Wired Doorbell 2nd Gen — Retinal 2K

  • This bracket is shaped specifically for the Ring Wired Doorbell (2nd Gen, 2026) — Amazon ASIN B0FJJ66YZ1. Ring's refreshed entry-level wired doorbell with Retinal 2K vision, head-to-toe view, and Smart Notifications.
  • Does NOT fit: the Ring Wired Doorbell Plus 2nd Gen, the Ring Wired Doorbell Pro 3rd Gen, the Pro PoE, the Wired Elite, the older Ring Pro / Pro 2, the Wired 2021 (1st gen), or any battery Ring doorbell. Each Ring doorbell has its own dedicated mount listing on our store.
  • Not sure which Ring you have? Send a photo of the back of your doorbell to shop@doorbellmount.com or text us — we'll confirm fit before you order.
Don't have the doorbell yet? Get the Ring Wired Doorbell 2nd Gen on Amazon →

Need help identifying a Ring model? Check our Ring Model Guide or our Best Ring Doorbells 2025 Guide.

Solve Side-Wall Views with a Wide 15-90° Pivot

Is your Ring Wired Doorbell 2nd Gen mounted on a side wall and only seeing siding? This Adjustable 15-90° Swivel Mount is engineered for exactly that problem. The dual-axis bent-neck joint pivots the doorbell outward across a wide 15° to 90° arc — so the Retinal 2K sensor faces the porch path instead of staring at the wall.

Side-wall installs are the #1 reason a perfectly good Ring Wired underdelivers: motion zones fire on every passing car, and the head-to-toe view captures the side of your house instead of your visitor. This mount fixes that geometry once and locks it permanently.

Wide Dual-Axis Control (15-90°) — Built for the Retinal 2K Lens

Designed for significant angle correction, this mount features a unique bent-neck swivel joint. Precise aiming control across a 15° to 90° arc relative to the wall — ideal for side-facing views (excels at angles greater than 45°). Fine-tuning is possible both horizontally (left/right) and vertically (up/down). Once the angle is set, the locking set screws hold position permanently — critical for Retinal 2K sharpness on any side-wall install.

15-90 degree side-wall swivel mount adjustability diagram for Ring Wired Doorbell 2nd Gen
15° to 90° pivot — dual-axis swivel for perpendicular-wall installs.

Note: this design is optimized for substantial side angles. If you only need a very minor (<15°) adjustment or a straight-ahead view, see our 0-35° Swivel Mount for the Ring Wired Doorbell 2nd Gen instead.

Internal Wire Routing — Hidden & Protected

Doorbell wiring (or PoE cable, where applicable) enters from the wall, passes through the hidden internal channel inside the swivel joint, routes through the front Ring Wired Doorbell 2nd Gen adapter bracket, and connects directly to the doorbell terminals. No exposed wiring, no weather risk — even at extreme 90° angles.

Internal wire routing diagram — wires pass cleanly through the 15-90 degree swivel mount and connect to the Ring Wired Doorbell 2nd Gen terminals

Mount Dimensions & Weight

  • Base Width: 1.8 inches
  • Base Height: 3.1 inches
  • Base Hole Spacing: 2-5/8 inches (center-to-center)
  • Wall Extension at 15°: ~2.0 inches
  • Wall Extension at 90°: ~3.5 inches (extends doorbell perpendicular to wall)
  • Weight: ~2 oz (PETG mount only)
  • (Note: This is the standard 1.8" base; narrow 3/4" baseplate option available — see Customization section.)

Key Features & Benefits

  • Wide Adjustable Angle (15-90°): Significant dual-axis swivel built specifically for side-wall / perpendicular installations.
  • Custom-Fit Bracket for Ring Wired Doorbell 2nd Gen: Pre-shaped Wired 2nd Gen pocket — no rocking, no rattle, no gap.
  • Secure Locking Set Screws: Once you set the angle, it stays. No drift in cold weather, no need to readjust after firmware updates.
  • Wire Pass-Through: Hole in the swivel joint routes the doorbell's power cable neatly — no exposed wiring at the joint.
  • Siding Compatible: Flat surfaces or lapped siding up to 1.8 inches wide.
  • Complete Kit: Adjustable base, custom Ring Wired Doorbell 2nd Gen bracket, and all necessary mounting screws.
  • Durable PETG: Sturdy 3D-printed PETG, UV-stable and freeze-tolerant for outdoor use.
  • Side-Wall Problem Solver: Eliminates the "side wall view" issue for proper security coverage of the porch.
  • Future-Proof Base: Base is compatible with future Ring doorbell adapter brackets — when Ring releases the next generation, just swap the small ~$10 adapter. Find replacement brackets here.

Customization & Add-On Options

We offer solutions for almost any mounting situation:

Installing Your 15-90° Side-Wall Mount on the Ring Wired Doorbell 2nd Gen

  1. Tools & Prep: Gather a drill, PH2 Philips (#6 base screws), PH1 Philips (#4 bracket/set/doorbell screws provided), wall anchors if needed, level, and a multimeter.
    16-24V AC, 10-40VA (a 30VA transformer is recommended for solid 2K Live View streaming and chime power)
  2. Plan the Aim Angle BEFORE Drilling: Stand where a visitor would stand. Visualize the angle from the doorbell location to that spot. 15-90° gives you a wide range — but committing to roughly the right angle before drilling pilot holes saves rework.
  3. Mount the Base: Route any existing doorbell wires through the base hole. Position vertical and attach using #6 screws (PH2 driver) with anchors as needed.
    Drill pilot holes if needed. Don't overtighten base screws.
  4. Attach the Swivel Bracket: Route wires through the swivel joint. Align onto the base and attach using four center screws (#4 / PH1 driver).
  5. Set Initial Angle: Adjust the swivel within 15-90° toward the visitor approach. Lightly tighten one or two set screws (#4 / PH1 driver) — final tightening comes after Live View confirmation.
  6. Wire the Ring Wired Doorbell 2nd Gen: Connect the two leads to the doorbell screw terminals — polarity doesn't matter for AC.
  7. Attach the Doorbell to the Bracket: Align the doorbell with the pre-drilled holes on the custom Wired 2nd Gen bracket. Secure using the screws PROVIDED WITH THIS MOUNT (#4 / PH1 driver). DO NOT USE the screws or wedge plate that came with your Ring doorbell.
    Tighten snugly, do not overtighten. Use the correct PH1 driver for provided screws.
  8. Aim Using Live View & Finalize Set Screws: Restore power. Open the Ring app → Live View. With the Retinal 2K head-to-toe lens, you'll see misalignment immediately. Adjust through the 15-90° range until the porch path is centered, then fully tighten the set screws.
    Do not overtighten set screws — hand-tight is sufficient. Over-tightening can crack the swivel joint.
  9. Tune Smart Notifications + Motion Zones: In the Ring app, redraw motion zones to match the new angle. Side-wall installs benefit from a tighter "porch path" zone — the wider 90° angle catches more peripheral motion (cars passing, mail truck) that you'll want to exclude.

Side-wall tip: extreme 90° angles slightly increase wind load on the doorbell. The set-screw lock is rated for it, but on installs in high-wind regions (coastal, exposed corners), the bracket's wider extension at 90° puts slight pre-loaded weight on the joint — completely fine, just normal for side-wall geometry.

FAQ — Ring Wired Doorbell 2nd Gen 15-90° Mount

Will this 15-90° swivel mount fit the Ring Wired Doorbell 2nd Gen (2026)?
Yes. This bracket is custom-shaped for the Ring Wired Doorbell 2nd Gen (2026), Amazon ASIN B0FJJ66YZ1. The doorbell sits flush in a model-specific pocket — no rocking, no rattle, no light gap. It will not fit other Ring models like the Wired Plus, Pro, Elite, or any battery Ring.
What's the difference between this 15-90° mount and the 0-35° mount for the same doorbell?
The 15-90° mount uses a bent-neck dual-axis pivot for substantial side-wall corrections — best when the doorbell is mounted perpendicular to the door (on a side wall, pillar, or outside corner). The 0-35° mount is for fine-tuning aim on flat-wall installs where the doorbell faces roughly toward the visitor already. If you need more than 15° of correction, choose the 15-90° version.
Can I install this on vinyl siding, Hardie board, or stucco?
Yes. The 1.8" base sits flat on most lapped siding. For vinyl siding without drilling into the siding itself, pair this mount with our Vinyl Siding Adapter. For Hardie/fiber-cement, use our Hardie Siding Mount. For stucco, drill pilot holes and use plastic anchors rated for masonry.
What hardware comes with the mount?
The kit includes the adjustable 15-90° swivel base, the custom Ring Wired 2nd Gen adapter bracket, locking set screws, mounting screws (#6 PH2 for the wall, #4 PH1 for bracket and doorbell), and basic wall anchors. You will need a drill, a Philips PH1 + PH2 driver, and a level. Use ONLY the screws provided — do NOT use the screws or wedge plate that came with the Ring.
Do I lose any features (HDR, Smart Notifications, Pre-Roll, etc.) by using an aftermarket mount?
No. The mount is a passive bracket — it has no electronics. All Ring features (Retinal 2K head-to-toe view, Smart Notifications, Live View, motion zones) work exactly as they would on the stock plate. After install, redraw motion zones in the Ring app to match the new aim angle.
Is the mount weatherproof? How long will the PETG last outdoors?
Yes. We print in UV-stabilized PETG (not PLA) which is rated for outdoor use, freeze-tolerant down to common winter temperatures, and won't yellow or warp like cheaper plastics. Real-world installs are still going strong after 4+ years.
Can I switch to a different Ring doorbell later without buying a whole new mount?
Yes. The base is universal across our Ring 15-90° line — only the small front adapter bracket is model-specific. Order a Replacement Bracket (~$10) when you swap doorbells and reuse the base on the wall.

Installation Video & Examples

Example 90 degree side wall doorbell installation Adjustable base component for side-wall doorbell mount
Watch: Swivel Doorbell Installation Video

(Video shows general installation principles for our swivel mounts.)

Need to Buy the Doorbell or Accessories?

Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases at no extra cost to you.

Questions? Need Help?

We're here to help! If you're unsure about your Ring model or need a custom solution for your 90-degree install:

Standard Color: Ships in Black. For other colors, use the Color Change Request.

Angle Note: The term "15-90°" represents the approximate adjustment range for perpendicular installations. Actual achievable angle depends on positioning.

3D-Printed Parts: Minor cosmetic variations or layer lines may be present and do not affect strength or weather resistance.

Order your Adjustable 15-90° Swivel Mount for the Ring Wired Doorbell 2nd Gen today — finally get the right view from your side-mounted doorbell.