15-90° Angle Mount for Vivint Doorbell Camera Pro (Gen 1) | Swivel the 180° Camera Toward Your Visitor

$50.00
$40.00
Side-Wall Angle Solution for the Vivint Doorbell Camera Pro (Gen 1) (15° to 90°) Custom-Fit for the Vivint Doorbell Camera Pro (Gen 1) Custom-shaped for the Vivint Doorbell Camera Pro (Gen 1) — the Gen 1 Vivint Doorbell Camera Pro...
Availability: Many In Stock
Product Type: Adjustable Mount 15-90°

Side-Wall Angle Solution for the Vivint Doorbell Camera Pro (Gen 1) (15° to 90°)

Custom-Fit for the Vivint Doorbell Camera Pro (Gen 1)

  • Custom-shaped for the Vivint Doorbell Camera Pro (Gen 1) — the Gen 1 Vivint Doorbell Camera Pro body (pro-installed, monitored).
  • Not a universal one-size mount: other doorbell brands use different body shapes and each has its own listing on our store.
  • Switching doorbells later? The base stays on the wall — grab a ~$10 Replacement Bracket for the new model.

Turn the Lens Toward Your Walkway

The Vivint Pro Gen 1's 1080p 180° view needs to face the doorstep. On a side wall, the stock plate aims it at the siding.

This adjustable 15-90° two-axis swivel joint mount swings the Vivint Doorbell Camera Pro (Gen 1) outward across a wide 15° to 90° arc so the 1080p 180° view lands on your visitor and the doorstep instead of the wall. Set screws lock the angle so it will not drift after the first windstorm or cold snap.

Dial In the Angle, Then Lock It

Built for real angle correction, the two-axis swivel joint lets you aim across a 15° to 90° arc relative to the wall — it shines above 45°. Adjust left/right and up/down, then tighten the set screws to lock it.

15-90 degree side-wall swivel adjustability diagram for Vivint Doorbell Camera Pro (Gen 1)
15° to 90° of dual-axis aim for perpendicular-wall installs.

Only need a small nudge (<15°) or a straight-ahead view? See our 0-35° Swivel Mount for the Vivint Doorbell Camera Pro (Gen 1) instead.

Internal Wire Routing

If the doorbell is hardwired (16-30V AC), the wires come out of the wall, pass through the concealed channel in the swivel, run through the front Vivint Doorbell Camera Pro (Gen 1) bracket, and land on the doorbell terminals — nothing exposed at the joint.

Concealed wire routing for the 15-90 degree swivel mount and Vivint Doorbell Camera Pro (Gen 1)

The Numbers

  • Base Width: 1.8 in
  • Base Height: 3.1 in
  • Base Hole Spacing: 2-5/8 in (center-to-center)
  • Reach at 15°: ~2.0 in
  • Reach at 90°: ~3.5 in
  • Weight: ~2 oz (mount only)
  • Standard 1.8" base; a narrow 3/4" baseplate is available — see Customization.

Key Features & Benefits

  • Custom Bracket for the Vivint Doorbell Camera Pro (Gen 1): A pre-shaped pocket cradles the body without blocking the lens, mic, or field of view.
  • UV-Stable PETG: Freeze-tolerant, weatherproof 3D-printed PETG made for year-round outdoor use.
  • Reusable Base: Switch doorbell brands later and just order a ~$10 Replacement Bracket — the base stays on the wall.
  • Made in the USA: Printed and shipped from our own shop, not mass-produced overseas.
  • Corner & Trim Friendly: Reaches past narrow trim and outside corners where the flat stock plate can't aim.
  • Wide 15-90° Angle: Two-axis swivel built specifically for side-wall and perpendicular installs.
  • Hidden Wire Pass-Through: An internal channel routes the low-voltage leads cleanly to the doorbell terminals.

Customize It

Installing It on the Vivint Doorbell Camera Pro (Gen 1)

  1. Power first. Kill power to the doorbell circuit at the breaker before you touch the wires.
    If hardwiring, confirm power is off with a multimeter before stripping wires.
  2. Grab your tools. Drill, PH2 (#6 wall screws), PH1 (#4 bracket/set/doorbell screws), a level, and anchors if you're not hitting a stud.
  3. Pick the angle before drilling. Stand where a visitor stands, picture the line from the doorbell to that spot, and rough in that angle so you don't re-drill.
  4. Mount the base. Line it up with your siding or trim and drive the #6 screws (PH2).
    Pilot-drill if needed and don't overtighten.
  5. Add the swivel. Feed the wires through the center (skip if battery) and fasten the swivel to the base with the four #4 / PH1 screws.
  6. Rough-set the aim. Turn it toward the walkway inside the 15-90° range and snug one or two set screws for now.
  7. Attach the Vivint Doorbell Camera Pro (Gen 1). Snap it on with the screws included with this mount (PH1). Do not reuse the stock back plate — our bracket replaces it.
  8. Confirm in the Vivint Smart Home app, then lock. Power up, open Live View, check the framing, and tighten all set screws hand-tight.
    Snug is enough — don't crank the set screws.
  9. Redraw detection zones. In the Vivint Smart Home app, tighten the motion zones to the new framing so you exclude the street and the neighbor's yard.

Good to Know

Is this the correct mount for the Vivint Doorbell Camera Pro (Gen 1)?
Yes — this bracket is cut to the Vivint Doorbell Camera Pro (Gen 1) body, so the doorbell drops into a model-specific pocket with the lens and mic clear. It does not fit other brands; each has its own listing.
What's the difference between the 15-90° and 0-35° mount?
The 15-90° version is for big side-wall corrections — when the doorbell sits on a perpendicular wall, pillar, or outside corner. The 0-35° version is for fine-tuning aim on a flat wall. If you need more than about 15° of turn, pick this one.
Can I use this on vinyl siding, Hardie board, or stucco?
Yes. The 1.8" base sits flat on most lapped siding. For vinyl siding without drilling the siding itself, add our Vinyl Siding Adapter; for fiber-cement, use our Hardie Siding Mount; for stucco, drill pilot holes and use masonry anchors.
What hardware is included?
You get the adjustable swivel base, the custom adapter bracket, locking set screws, mounting screws (#6 PH2 for the wall and #4 PH1 for the bracket and doorbell), and wall anchors. Use only the screws provided, not the doorbell's stock backplate screws.
Will it hold up outdoors, and for how long?
Yes. We print in UV-stabilized PETG (not brittle PLA), so it's freeze-tolerant and won't yellow or warp. Real-world installs are still going strong after 4+ years.

✔ Replacement Guarantee — The Right Part, Guaranteed

Send a photo of your install spot and doorbell BEFORE you order and we'll point you to the exact part. If you order and it doesn't fit, we'll send the correct one at NO additional cost.

  • Before ordering: text or email photos of (1) the install location and (2) the doorbell; we'll confirm the fit.
  • If it doesn't fit: send a photo of the doorbell and the fit problem — we ship the correct part free.
  • Reach us: 833-326-6868 / shop@doorbellmount.com.
Where to get this doorbell: The Vivint Doorbell Camera Pro is sold and installed through Vivint Smart Home (not on Amazon). This mount fits the doorbell you already have installed.

Questions?

Standard Color: Black. Other colors via the Color Change Request.

Angle Note: "15-90°" is the approximate range for perpendicular installs; actual angle depends on positioning.

3D-Printed: minor layer lines may show and do not affect strength or weather resistance.

Fix that perpendicular-wall view on your Vivint Doorbell Camera Pro (Gen 1). Made in the USA, shipped in 2-3 business days.