15-90° PoE Swivel Mount for Ubiquiti UniFi G4 Doorbell (non-Pro) | Cat-5e Pass-Through Side-Wall Bracket

$50.00
$40.00
Aim Your Ubiquiti UniFi G4 Doorbell (non-Pro) Off a Side Wall: 15-90° Swivel Mount Custom-Fit for the Ubiquiti UniFi G4 Doorbell (non-Pro) Custom-shaped for the Ubiquiti UniFi G4 Doorbell (non-Pro) — Amazon ASIN B08L3X9ZZX — the original single-camera UniFi G4...
Availability: Many In Stock
Product Type: Adjustable Mount 15-90°

Aim Your Ubiquiti UniFi G4 Doorbell (non-Pro) Off a Side Wall: 15-90° Swivel Mount

Custom-Fit for the Ubiquiti UniFi G4 Doorbell (non-Pro)

  • Custom-shaped for the Ubiquiti UniFi G4 Doorbell (non-Pro) — Amazon ASIN B08L3X9ZZX — the original single-camera UniFi G4 Doorbell (not the dual-cam G4 Pro). The joint fits a terminated Cat-5e/Cat-6 pass-through.
  • Not a universal one-size mount: other doorbell brands use different body shapes and each has its own listing on our store.
  • Switching doorbells later? The base stays on the wall — grab a ~$10 Replacement Bracket for the new model.
Don't have the doorbell yet? Get the Ubiquiti UniFi G4 Doorbell (non-Pro) on Amazon →

Fix a Perpendicular or Corner Mounting Spot

The UniFi G4's single 5MP 155° lens belongs pointed at your doorstep. On a side wall, the stock plate aims it at the siding.

This adjustable 15-90° angled swivel arm mount swings the Ubiquiti UniFi G4 Doorbell (non-Pro) outward across a wide 15° to 90° arc so the 5MP 155° view lands on your visitor and the doorstep instead of the wall. Set screws lock the angle so it will not drift after the first windstorm or cold snap.

How Far It Swivels

Built for real angle correction, the angled swivel arm lets you aim across a 15° to 90° arc relative to the wall — it shines above 45°. Adjust left/right and up/down, then tighten the set screws to lock it.

15-90 degree side-wall swivel adjustability diagram for Ubiquiti UniFi G4 Doorbell (2020)
15° to 90° of dual-axis aim for perpendicular-wall installs.

Only need a small nudge (<15°) or a straight-ahead view? See our 0-35° Swivel Mount for the Ubiquiti UniFi G4 Doorbell (non-Pro) instead.

No Exposed Wiring at the Joint

If the doorbell is hardwired (PoE 802.3af or 16-24V AC), the wires come out of the wall, pass through the concealed channel in the swivel, run through the front Ubiquiti UniFi G4 Doorbell (non-Pro) bracket, and land on the doorbell terminals — nothing exposed at the joint.

Concealed wire routing for the 15-90 degree swivel mount and Ubiquiti UniFi G4 Doorbell (2020)

Measurements & Reach

  • Base Width: 1.8 in
  • Base Height: 3.1 in
  • Base Hole Spacing: 2-5/8 in (center-to-center)
  • Reach at 15°: ~2.0 in
  • Reach at 90°: ~3.5 in
  • Weight: ~2 oz (mount only)
  • Standard 1.8" base; a narrow 3/4" baseplate is available — see Customization.

What You Get

  • Custom Bracket for the Ubiquiti UniFi G4 Doorbell (non-Pro): A pre-shaped pocket cradles the body without blocking the lens, mic, or field of view.
  • Siding Compatible: Sits flat on flat surfaces or lapped siding up to 1.8 inches wide.
  • Complete Kit: Adjustable base, custom Ubiquiti UniFi G4 Doorbell (non-Pro) bracket, and all the mounting screws you need.
  • UV-Stable PETG: Freeze-tolerant, weatherproof 3D-printed PETG made for year-round outdoor use.
  • Reusable Base: Switch doorbell brands later and just order a ~$10 Replacement Bracket — the base stays on the wall.
  • Made in the USA: Printed and shipped from our own shop, not mass-produced overseas.
  • Corner & Trim Friendly: Reaches past narrow trim and outside corners where the flat stock plate can't aim.

Customize It

Installing It on the Ubiquiti UniFi G4 Doorbell (non-Pro)

  1. Power first. Kill power to the doorbell circuit at the breaker before you touch the wires.
    If hardwiring, confirm power is off with a multimeter before stripping wires.
  2. Grab your tools. Drill, PH2 (#6 wall screws), PH1 (#4 bracket/set/doorbell screws), a level, and anchors if you're not hitting a stud.
  3. Pick the angle before drilling. Stand where a visitor stands, picture the line from the doorbell to that spot, and rough in that angle so you don't re-drill.
  4. Mount the base. Line it up with your siding or trim and drive the #6 screws (PH2).
    Pilot-drill if needed and don't overtighten.
  5. Add the swivel. Feed the wires through the center (skip if battery) and fasten the swivel to the base with the four #4 / PH1 screws.
  6. Rough-set the aim. Turn it toward the walkway inside the 15-90° range and snug one or two set screws for now.
  7. Attach the Ubiquiti UniFi G4 Doorbell (non-Pro). Snap it on with the screws included with this mount (PH1). Do not reuse the stock back plate — our bracket replaces it.
  8. Confirm in the UniFi Protect app, then lock. Power up, open Live View, check the framing, and tighten all set screws hand-tight.
    Snug is enough — don't crank the set screws.
  9. Redraw detection zones. In the UniFi Protect app, tighten the motion zones to the new framing so you exclude the street and the neighbor's yard.

Questions Buyers Ask

Does this fit the Ubiquiti UniFi G4 Doorbell (non-Pro) specifically?
Yes — this bracket is cut to the Ubiquiti UniFi G4 Doorbell (non-Pro) body, so the doorbell drops into a model-specific pocket with the lens and mic clear. It does not fit other brands; each has its own listing.
Will it hold up outdoors, and for how long?
Yes. We print in UV-stabilized PETG (not brittle PLA), so it's freeze-tolerant and won't yellow or warp. Real-world installs are still going strong after 4+ years.
Does the mount block the camera or speaker at steep angles?
No. The bracket holds the doorbell clear of the lens and mic across the entire 15-90° range, so the picture and two-way audio stay unobstructed even at a hard 90° turn.
What if I order and it doesn't fit?
Send us a photo of your doorbell and the fit issue and we'll ship the correct part at no extra cost — see our Replacement Guarantee below.
How fast does it ship?
Each mount is printed to order and typically ships within 2-3 business days from our USA shop.

✔ Replacement Guarantee — The Right Part, Guaranteed

Send a photo of your install spot and doorbell BEFORE you order and we'll point you to the exact part. If you order and it doesn't fit, we'll send the correct one at NO additional cost.

  • Before ordering: text or email photos of (1) the install location and (2) the doorbell; we'll confirm the fit.
  • If it doesn't fit: send a photo of the doorbell and the fit problem — we ship the correct part free.
  • Reach us: 833-326-6868 / shop@doorbellmount.com.

Need the Doorbell?

Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases at no extra cost to you.

Questions?

Standard Color: Black. Other colors via the Color Change Request.

Angle Note: "15-90°" is the approximate range for perpendicular installs; actual angle depends on positioning.

3D-Printed: minor layer lines may show and do not affect strength or weather resistance.

Dial in the perfect angle on your Ubiquiti UniFi G4 Doorbell (non-Pro). Made to order and shipped within 2-3 business days.