0-35° Adjustable Mount for the Ring Wired Doorbell Pro (PoE Edition)
This is a clean-install 0-35° swivel mount designed around the Ring Pro PoE — including a wire pass-through sized for terminated CAT5e/CAT6 with intact RJ45 connectors so you don't have to recrimp after fishing the cable through the wall. The dual-axis ball joint gives you continuous angle adjustment up to 35° in any direction, and the low-profile body sits just 1.5" off the wall to keep the install discreet — exactly what someone who picked PoE over a doorbell transformer would want. PETG construction, custom Pro PoE adapter pocket, all hardware included.
Engineered for Ring's Power-over-Ethernet Pro Doorbell
Custom bracket for the Ring Wired Doorbell Pro, Power over Ethernet — Amazon ASIN B0F7TFNLD1. Released 2026 alongside the standard Pro 3rd Gen, the PoE version delivers the same Retinal 4K, 10x Enhanced Zoom, and Low-Light Sight, but powered and connected via a single CAT5+ cable instead of doorbell wires.
Body geometry is identical to the standard Pro 3rd Gen, so this bracket fits both — listed separately so customers searching for "Pro PoE" find this exact match.
Does NOT fit: the older Ring Pro 2 (curved back), the original Pro (flat with ridges), the Wired Doorbell Plus 2nd Gen, the Elite, or any battery model.
One Cable for Power and Data — Don't Waste It on a Bad Angle
If you went with the PoE version of the Pro, you cared about a clean install: no doorbell transformer to fail in 5 years, no separate WiFi chunk, just one CAT5+ run from your network closet. You picked precision — so why mount it pointing the wrong way? This swivel matches the install philosophy: aim once, lock down, never touch it again.
0-35° Two-Axis Aiming
One precision ball joint. Up, down, left, right — independently or combined. Lock down with set screws and the angle holds even if a delivery driver leans on it.
Internal Wire Routing — Hidden & Protected
Low-voltage wires enter from the wall, pass through the hidden internal channel inside the ball-joint mount, route through the front adapter, and connect directly to the doorbell terminals. No exposed wiring, no weather risk.
Mount Dimensions
- Base Width: 1.8 inches
- Base Height: 3.1 inches
- Hole Spacing: 2-5/8 inches center-to-center
- Wall Extension at 0°: ~1.5 inches
- Cable Pass-Through: Sized for CAT5e/CAT6 with intact RJ45 — pass cleanly through the joint.
Why This Mount for PoE Installs
- CAT5+ Cable Routes Cleanly: Wire pass-through sized for Ethernet with terminated RJ45 — no recrimping.
- Snug Fit on the Pro PoE Body: Pre-shaped pocket — same as the Pro 3rd Gen since they share geometry.
- Two-Axis 0-35° Range: Aim the 4K Retinal sensor precisely; lock with set screws.
- Outdoor-Rated PETG: Built for years outside in any climate.
- Universal Swivel Base: Future doorbell upgrades only need a new ~$10 adapter.
- Siding Compatible: Flat surfaces and lapped siding up to 1.8" — including new-construction fiber cement.
- Complete Hardware Kit: All screws and anchors included.
Installing with the Ring Pro PoE
-
Pre-Stage the Cable: Run your CAT5e or CAT6 to the doorbell location and terminate with an RJ45 BEFORE attaching the mount — easier than fighting the bracket later.
Outdoor-rated cable is recommended for any external run. UV will degrade indoor-rated PVC jacket within a couple of years.
- Mount the Base: Pull cable through, position vertical or horizontal, attach with #6 screws (PH2 driver). Anchors as needed.
- Attach the Swivel: Route cable through, screw onto base with #4 / PH1 center screws.
- Connect the Doorbell: Plug RJ45 into the back of the Pro PoE. PoE+ delivers both power and data — no transformer required.
- Mount the Doorbell: Use the PROVIDED screws with this mount — not Ring's stock hardware.
- Verify Power & Aim: Confirm LED activity, connect via the Ring app, fine-tune the angle in Live View, lock the set screws.
Pro install tip: tag both ends of the Ethernet run before fishing it through the wall. Future-you will thank you when troubleshooting.
Questions About Fitment or PoE?
- Email: shop@doorbellmount.com
- Text/Call: 1-833-326-6868
Standard Color: Ships in Black. Other colors via Color Change Request.
Need to Buy the Doorbell Too?
Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases. Same Amazon price for you, small commission for us.
Angle Note: Maximum 35° angle is approximate; range varies slightly with surface and orientation.
3D-Printed Parts: Minor visible layer lines are normal and do not affect strength or weather resistance.
Clean PoE install deserves a clean swivel mount. Order the dedicated Pro PoE bracket today.
