Adjustable 0-35° Swivel Mount for Ring Wired Doorbell Plus (2nd Gen)
A precision dual-axis ball-joint mount custom-cut for the Ring Wired Doorbell Plus (2nd Gen). The swivel runs smooth across the entire 0-35° range — left, right, up, down, or any blend — and locks down with set screws so the angle stays exactly where you put it. The bracket pocket is shaped to the Plus 2nd Gen body so the doorbell sits flush with no gap, no rocking, no wind chatter. PETG plastic stands up to UV, freeze cycles, and salt air. Custom adapter and full hardware kit included.
Made for Ring's Mid-Tier 2K Wired Doorbell
Custom-fit for the Ring Wired Doorbell Plus (2nd Gen) — Amazon ASIN B0F9CN26NX, released 2025 with Retinal 2K, 6x Enhanced Zoom, Low-Light Sight, and the redesigned slimmer industrial body. Different mounting footprint than the original Wired Plus (old Ring Pro), so legacy brackets won't fit.
Does NOT fit: the original Ring Wired Plus (old Pro), the Wired Doorbell (2nd Gen) basic, the Wired Pro 3rd Gen, or the Pro PoE. Each has its own dedicated mount listing.
Confused by Ring's naming? You're not alone. Send us a photo and we'll confirm before you order.
Don't Waste Retinal 2K on a Bad Angle
Retinal 2K isn't just more pixels — it's Ring's on-device AI cleaning up the image so faces, license plates, and package labels stay sharp even in low light. None of that matters if the doorbell is mounted on a side wall pointing at a hedge. This 0-35° swivel mount tilts and rotates in two directions so you can dial in exactly the right view.
Two-Axis Adjustment, 0-35° Each Direction
One ball joint. Tilt up, down, left, right — set it once, lock it, never touch it again.
Internal Wire Routing — Hidden & Protected
Low-voltage wires enter from the wall, pass through the hidden internal channel inside the ball-joint mount, route through the front adapter, and connect directly to the doorbell terminals. No exposed wiring, no weather risk.
Mount Dimensions
- Base Width: 1.8 inches
- Base Height: 3.1 inches
- Hole Spacing: 2-5/8 inches center-to-center
- Wall Extension at 0°: ~1.5 inches
What's Included & Why It Matters
- Custom Bracket Shaped to the Ring Plus 2nd Gen Body: Snug fit, no gap for water intrusion or rattling.
- Smooth 0-35° Ball Joint: Two-axis aim — perfect for the new wide-FOV Retinal sensor.
- Locking Set Screws: Tighten once and the angle holds permanently.
- Wire Pass-Through Joint: Hides transformer wires inside the swivel.
- Mounts on Siding up to 1.8" Wide: Flat surfaces, lapped vinyl, fiber cement, brick, stucco.
- Future-Proof Universal Base: Upgrade later? Swap the small ~$10 adapter only.
- Outdoor-Ready PETG: 3D-printed weather-resistant filament.
Installing on the Ring Wired Plus 2nd Gen
-
Power Off: Flip the breaker for the doorbell circuit.
Confirm with a multimeter — the Plus 2nd Gen has more onboard electronics than the basic Wired model. A live wire short during install can brick it.
- Mount the Base: Pull the doorbell wires through, attach to siding/stucco/brick with #6 screws (PH2). Anchors if not into a stud.
- Attach the Swivel: Route wires through, screw onto the base with four center screws (#4 / PH1). Don't fully tighten yet.
- Wire the Ring Plus 2nd Gen: Connect the two transformer leads per Ring's setup guide. Tuck slack neatly into the cavity.
- Slot the Doorbell into the Bracket: Use the screws provided with this mount — not Ring's wedge plate or stock screws.
- Aim & Lock: Power back on. Open the Ring app, fine-tune in Live View, tighten the set screws.
Pro tip: Open Live View in landscape on your phone while you adjust — the Retinal 2K image makes small angle changes easier to see than the older models.
Questions About Fitment?
- Email: shop@doorbellmount.com
- Text/Call: 1-833-326-6868
Standard Color: Ships in Black. Other colors via Color Change Request.
Don't Have the Doorbell Yet?
Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases. Same Amazon price for you; small commission for us.
Angle Note: Maximum 35° angle is approximate; actual range varies slightly with surface and orientation.
3D-Printed Parts: Minor surface layer lines are normal and do not impact strength.
Stop tilting the camera with shims and tape — install a real swivel mount built for the Ring Wired Plus 2nd Gen.
