Adjustable 0-35° Swivel Mount for the Eufy Video Doorbell C30
An angle-adjustable mount built specifically for the Eufy Video Doorbell C30 — the battery-only 2K model with a 165° ultra-wide field of view. The bracket is contoured to the C30's compact body, holds it square against the wall, and the smooth 0-35° ball joint lets you swing the wide-angle lens away from any obstruction (a porch wall, a doorframe, a trim molding) so all 165° of view actually points at your visitors. Made from UV-stable outdoor PETG, set-screw locked, and printed to order in our shop.
Fits ALL Eufy Video Doorbell Models
This swivel mount is fully compatible with the Eufy Video Doorbell C30 — and with every other Eufy video doorbell on the market. Eufy designed their lineup with a consistent mounting footprint, so this same bracket also fits the E340 (2K dual cam), the S330 (wired and battery dual cam), the C31 (2K wired or battery), the S220 (2K battery), the C210 (1080p budget battery), and the original Eufy 2K Wired, 2K Battery, and Dual cam (HomeBase) models. Upgrade or change between Eufy doorbells anytime — no new mount needed.
Will NOT fit other brands — Ring, Nest, Wyze, Blink, Arlo, and all non-Eufy doorbells use different body geometries. If you switch to a different brand of doorbell in the future, you don't need to buy a new mount — just order the matching adapter bracket (~$10) from our Replacement Bracket listing. The swivel base stays installed on your wall.
Not sure which Eufy you have? Doesn't matter — this mount fits all of them. Text us a photo if you have any questions.
Position the 165° Wide View Where It Counts
The C30's headline feature is a massive 165° field of view — wider than almost any competitor. But a wide lens only helps if the lens is pointed at the right zone. Mount it flat on a wall that's offset from the door, and a third of that 165° is staring at your siding. A small swivel adjustment shifts the entire view to where it's useful: across the porch, up the path, toward the steps.
This 0-35° dual-axis mount gives you that adjustment with a couple of degrees of precision, then locks it permanently with set screws. The C30 also has no chime wires to deal with (it's battery-only), which makes installation a 15-minute job.
Two-Axis Aiming, 0-35° Range
One smooth ball joint. Aim left, right, up, or down — all the way to 35° in any direction. Lock the angle with set screws. Done.
Internal Wire Routing — Hidden & Protected
Low-voltage wires enter from the wall, pass through the hidden internal channel inside the ball-joint mount, route through the front adapter, and connect directly to the doorbell terminals. No exposed wiring, no weather risk.
Mount Dimensions
- Base Width: 1.8 inches
- Base Height: 3.1 inches
- Hole Spacing: 2-5/8 inches center-to-center
- Wall Extension at 0°: ~1.5 inches (low-profile)
- Narrow 3/4" baseplate option available for thin trim — see Customization below.
What You Get
- Custom Bracket for C30: Pre-shaped pocket — zero rattle, zero lens obstruction.
- Dual-Axis 0-35° Swivel: Aim the ultra-wide lens precisely; lock with set screws.
- Battery-Only Friendly: No wire pass-through complications — the C30 doesn't have chime wires.
- Outdoor-Rated PETG: Matches the C30's IP65 weather tolerance.
- Siding Compatible: Flat or lapped siding up to 1.8" wide.
- Future-Proof Base: Universal swivel — swap doorbells later for ~$10.
- Complete Kit: Base, custom C30 bracket, all required mounting screws.
- Charging Access: The bracket is open at the bottom edge so the C30's USB-C port is reachable for tabletop or in-place charging.
Installing on the Eufy Video Doorbell C30
-
Charge First: The C30 ships partially charged — top it off (USB-C, ~3 hours) before mounting so you can verify Live View aim during install.
No wiring needed. The C30 is battery-only and doesn't connect to a transformer or existing chime.
- Mount the Base: Position the base vertically or horizontally to suit your siding/trim. Drill pilot holes if needed and screw in with #6 screws / PH2 driver. Use anchors if not hitting a stud.
- Attach the Swivel: Screw the swivel onto the base with four #4 / PH1 center screws.
- Pair the C30 in the App: If you haven't already, pair it via the eufy Security app and your HomeBase or directly to Wi-Fi.
- Snap the C30 In: Use the screws PROVIDED WITH THIS MOUNT (PH1 driver) — not Eufy's plate.
- Aim & Lock: In Live View, swing the swivel until the 165° frame covers your porch correctly. Tighten the set screws.
Tip: with a 165° lens, even small angle changes shift the framing dramatically. Make small swivel adjustments (a few degrees at a time) and check Live View between each.
Questions About Fitment?
- Email: shop@doorbellmount.com
- Text/Call: 1-833-326-6868
Standard Color: Ships in Black. Other colors via Color Change Request.
Need to Buy Your Eufy Doorbell?
Quick links via our Amazon Associates account — current Eufy lineup:
- Eufy Video Doorbell E340 (2K Dual Cam, Wired or Battery) — B0CD7NT4Y9
- Eufy Video Doorbell C31 (2K, Wired or Battery, Quick-Release) — B0DDTT29C2
- Eufy Video Doorbell C30 (2K, Battery, 165° View) — B0DDTSK2WP
- Eufy Video Doorbell S330 Wired (2K HDR Dual Cam) — B09Q2NGQL8
- Eufy Video Doorbell S220 (2K Battery, 180-Day) — B081C4JN51
- Eufy Video Doorbell C210 (1080p Battery) — B08DXD8LSR
- Browse all Eufy doorbells on Amazon →
Affiliate Disclosure: As an Amazon Associate, DoorbellMount.com earns from qualifying purchases at no extra cost to you. Pricing is controlled by Amazon and may change.
Angle Note: The 35° maximum is approximate; actual range varies slightly by surface and orientation.
3D-Printed Parts: Minor visible layer lines are normal and do not affect strength. Each mount is printed-to-order in our USA shop.
Get the angle right on your Eufy doorbell — order today and we'll print it within 24-48 hours.
