Eufy Doorbell Standard Offset Brick Extension Mount (S330/E340/S220/C210)
Compatibility: Eufy Doorbells (Single & Dual Camera)
-
Fits Eufy Models Including:
- Eufy S330 (Dual Cam)
- Eufy E340 (Dual Cam)
- Eufy S220 / C210 (Single Cam - Wired/Wireless)
- (Leave a note with your specific Eufy model at checkout if possible, especially if it's not listed above, as some have model-specific brackets for a better fit.)
- WILL NOT FIT: Doorbells from other brands (Ring, Nest, etc.).
- Surface Width: Requires mounting surface (trim/molding) to be AT LEAST 9/16 inches wide for the base.
Please double-check your Eufy model or send us a picture if unsure!
Extend Your Eufy Doorbell Past Brick with Standard Offset!
Is your Eufy Doorbell (S330, E340, S220, C210, etc.) mounted on trim set back behind brick or stone? Need clearance for a storm door? This **Standard Offset Brick Extension Mount** brings your doorbell forward for improved visibility and provides a moderate sideways shift.
It mounts easily onto your existing trim (minimum 9/16" wide) without drilling into masonry, positioning your Eufy doorbell correctly relative to the brick face.
How it Works: Standard 5/8" Offset Extension
This mount uses our popular STANDARD OFFSET. The center of your Eufy Doorbell will be shifted approximately 5/8 inches horizontally towards the brick side relative to the center of the narrow 9/16" mount base. This typically leaves about **3/8 inch** of the base visible near the door frame.
This configuration works well for most installations, partially positioning the doorbell over the adjacent brick and providing good door clearance. The offset is reversible for left or right installation.
This mount positions the doorbell over or in front of the brick face.
Standard Offset (This Product) vs Full Offset:
Need Maximum Sideways Clearance? Click here for the Full Offset version for Eufy Doorbells.Base Dimensions & Mounting: The extension base is 9/16 inches wide (requires >= 9/16" surface). Standard mounting hole spacing is 2.5 inches (center-to-center). Ensure solid mounting on trim. Wall-mounting screws not included.
Angled Trim? If your trim is angled, add our Angle Shims (sold separately) for a perpendicular installation.
CRITICAL: Measure & Select Your Extension Length!
Choose the correct length to clear your brickwork or storm door. Measure carefully:
- Measure the exact distance straight out from the surface where the mount base will attach (your trim) to the outermost face of your brick or obstacle.
- Order THIS measurement as your required Extension Length. (Do NOT subtract doorbell thickness for offset mounts).
Select the required extension length from the dropdown menu when ordering. (Starts at 1/4 inch).
Need help measuring? Text/email a picture! (Contact info below)
Measure like this from Trim to Brick Face for Extension Length.
Key Features & Benefits:
- Fits Most Eufy Doorbells: Compatible with Single Cam (S220, C210 - Wired/Wireless) & Dual Cam (S330, E340). Leave note with specific model for best bracket fit.
- Standard 5/8" Offset: Provides effective sideways positioning for common needs.
- "Over Brick" Placement: Extends doorbell forward past brick, positioning it partially over the brick face.
- Avoid Drilling Brick: Mounts easily to existing trim (>=9/16" wide, Std. 2.5" hole spacing).
- Selectable Extension Length: Order the precise depth needed (Trim-to-Brick/Obstacle measurement).
- Narrow Base (9/16" Std): Designed for standard trim widths.
- Wire Passthrough: Internal channel accommodates optional wiring.
- Reversible Offset: Base can be flipped for left or right offset.
- Durable PETG Construction: Strong, weather-resistant plastic.
- Add-on Compatible: Works with angle shims, fillers etc. (see below).
- Future-Proof Bracket: Top adapter bracket potentially replaceable for future upgrades (check compatibility).
How to Install Your Standard Offset Extension for Eufy
This mount uses two main printed pieces: the Extension Base and the Doorbell Adapter Bracket.
-
Tools & Prep: Gather: Drill, PH1 & PH2 Philips Bits, Level, Anchors (if needed), your Eufy doorbell backplate & hardware.
Turn OFF power at the breaker if hardwiring! Ensure doorbell is charged if battery version.
-
Mount Extension Base: Position the Extension Base (correct length/offset) on trim over wires (ensure offset is desired direction L/R). Attach securely using appropriate screws (#6 size likely, use PH2) and anchors into the 2.5" spaced holes.
Ensure base is level. Don't overtighten.
-
Attach Doorbell Adapter Bracket: Route wires through the Doorbell Adapter Bracket (top piece for Eufy). Align onto Extension Base. Attach using the four small center screws provided (likely #4 screws / PH1 driver).
Use correct PH1 bit. Tighten until flush. Do NOT over-torque.
-
Attach Eufy Backplate: Secure the **backplate/wedge that came WITH your Eufy Doorbell** onto the Doorbell Adapter Bracket using the small screws PROVIDED WITH THIS MOUNT (typically #4 / PH1). Ensure correct orientation.
Do NOT use Eufy's long wall screws here. Use correct PH1 driver.
- Wire & Mount Eufy Doorbell: Connect wires (if applicable) to the Eufy backplate following Eufy's instructions. Click the Eufy Doorbell unit firmly onto its backplate until secure.
- Final Check & Power On: Ensure doorbell is secure. Turn power back on (if applicable) and test.
Follow safety rules & Eufy guidelines. Use correct anchors/screws. Correct screwdriver size prevents stripping.
Optimize Your Eufy Doorbell Placement
Optimized Design for Brick Surfaces
The Eufy Doorbell Brick Extension is specifically designed for homes with brick walls near trim. This extension features a 9/16 inch wide base and standard offset, ensuring a sturdy installation that allows your Eufy Doorbell (Single or Dual Cam) to stay securely mounted and capture the best view, overcoming obstructions.
Easy Installation Process
Installing the Eufy Doorbell Brick Extension onto existing trim is straightforward. The included hardware simplifies the process, making it accessible even for DIY beginners, enhancing your home security setup quickly and efficiently.
Durable and Weather-Resistant Materials
Constructed with high-quality PETG, this extension is built to withstand outdoor elements. It remains durable in harsh weather, ensuring your Eufy doorbell operates reliably year-round, giving you peace of mind.
Optional Add-ons & Accessories:
Further customize your installation:
-
Angle Shims (5°, 10°, 15°)Corrects for angled trim *under the Extension Base*.
-
Horizontal Angle Adapter or Swivel Add-onAdd horizontal angle adjustment to the end of the extension.
-
Bottom Filler Spacer PlateFills the gap below the extension base on angled/uneven trim.
-
Body Shim Filler PlateFills gaps between the extension body and uneven brick.
-
Add Side Wire EntryAdds side entry holes ("mouse holes") to the *Extension Base* (add service to cart).
-
Wire Extension Kit
Need longer wires? Purchase our extension wire kit with your choice of connectors.
Standard color is Black. For White, Brown, Grey, etc., add this service.
Product Examples
(See listing photos for details or contact us for more examples!)
Need Help? Confirm Compatibility & Measurements!
Ensure you have a compatible Eufy Doorbell model. Need help measuring extension length or choosing Standard vs Full Offset?
- Email: shop@doorbellmount.com (Send Pictures!)
- Text/Call: 1-833-326-6868 (Text Pictures!)
Standard Color: Black. For other colors, add the Color Change Request item.
Doorbell Not Included. Includes the 2-piece extension mount (Extension Base + Doorbell Adapter Bracket for Eufy) and necessary assembly screws.
PETG Material: Printed in durable, outdoor-rated PETG.
3D Printed Quality: Minor cosmetic variations inherent to 3D printing may exist but do not affect function. Contact us with quality concerns before reviewing.
Order the Standard Offset Brick Extension for your Eufy Doorbell today! Remember to measure carefully (Trim to Brick Face!) and select your required extension length.
