Adjustable Swivel Mount (0-35°) for Ring Wired Doorbell Plus (formerly Pro)
Compatibility Warning: Check Your Ring Pro Model Carefully!
This mount is specifically designed ONLY for the model now called Ring Wired Doorbell Plus (previously known as the original Ring Pro or "Pro 1"). Key identifier: It has a Flat Back with Ridges.
(As an Amazon Associate, I earn from qualifying purchases.)
CRITICAL: This mount DOES NOT FIT the newer Ring Wired Doorbell Pro (also known as the Pro 2).
Confused? Please send us a picture before ordering!
Need help? Email shop@doorbellmount.com or Text 1-833-326-6868. Check our Ring Model Guide.
Fine-Tune Your View with the 0-35° Low-Profile Swivel Mount
Need a subtle angle adjustment for your Ring Wired Doorbell Plus (Pro 1)? This low-profile swivel mount provides precise aiming control with a 0° to 35° adjustment range. Its versatile dual-axis joint allows fine-tuning both horizontally (left/right) and vertically (up/down).
Perfect for situations where your doorbell is mounted near the door on the same wall and needs just a slight turn inward, or needs a minor up/down tilt to capture the ideal view. This is the flatter version without the extended neck found on our 90° models.
Precise Dual-Axis Control (0-35°)
Gain exact control over your camera's perspective. The smooth swivel joint enables fine adjustments across a 0° to 35° arc relative to the mounting surface, ensuring you capture precisely what matters.
Flexible Base Positioning: The base can be installed with screw holes aligned vertically (standard) or horizontally if needed by your mounting surface (e.g., narrow horizontal trim). The doorbell remains upright regardless of base orientation.
Mount Dimensions
- Base Width: 1.8 inches
- Base Height: 3.1 inches
- Base Hole Spacing: 2-5/8 inches (center-to-center)
- Total Extension (@ 0° Angle): Approx. 1.5 inches from wall
- (Note: Base dimensions are the same for 35° and 90° swivel mounts; total extension varies for 90° mount depending on angle)
Key Features & Benefits:
- Customized Fit: Exclusively for Ring Wired Doorbell Plus (formerly Pro) - Verify Your Model!
- Subtle Angle Correction (0-35°): Dual-axis swivel perfect for fine-tuning horizontal & vertical views.
- Low-Profile Design: Sits closer to the wall than the 90° version.
- Secure Angle Locking: Set screws included (likely #4 / PH1) to firmly hold your precise angle.
- Versatile Mounting: Base installs vertically or horizontally; fits surfaces/siding up to 1.8" wide. Adapters available for narrower spots (down to 1/2").
- Clean Wire Management: Central hole for wire passthrough.
- Outdoor Ready: Durable PETG construction withstands the elements.
- All Hardware Included: Comes with necessary screws for base, bracket, doorbell body, and angle locking.
How to Install Your 0-35° Swivel Mount
-
Prepare Tools & Area: Gather necessary tools:
- Drill (with appropriate bits).
- Screwdrivers/Bits: PH2 Philips (#6 base screws) AND PH1 Philips (#4 bracket/set/doorbell body screws provided by us). Use correct size!
- Wall anchors (if needed). Level (optional).
Turn OFF power to doorbell wiring at the breaker before starting!
-
Mount the Base: Route wires through the base piece. Position base (screws vertical or horizontal) and attach securely using provided #6 screws (PH2 driver) or suitable anchors.
Drill Warning: Use low speed/clutch. Do not overtighten (risk of stripping screws or cracking plastic).
-
Attach Swivel Bracket: Route wires through the swivel bracket. Align onto base and attach using the four center screws provided (likely #4 screws / PH1 driver).
Stripping Warning: Use correct PH1 driver. Tighten snugly by hand first, avoid overtightening with drill.
- Set Initial Angle: Adjust swivel bracket (up/down & left/right) within the 0-35° range. Lightly tighten one/two set screws (likely underside, #4 / PH1 driver).
- Wire Your Doorbell: Connect wires following Ring's instructions. Tuck excess wire into the mount cavity.
-
Attach Doorbell to Mount Bracket:
- Align your Ring Wired Doorbell Plus (or its plate if used) with the pre-drilled holes on the swivel mount bracket.
- Secure doorbell/plate using the shorter screws PROVIDED WITH THIS MOUNT (likely #4 screws / PH1 driver).
- DO NOT USE screws that came with your doorbell for this step (they may be too long).
- Replace cover if applicable.
Stripping Warning: Use correct PH1 driver for provided screws. Tighten snugly, do not overtighten with drill.
-
Finalize Angle & Secure: Make final angle adjustments. Fully tighten all set screws using the correct driver (likely PH1) and gentle pressure.
Do not overtighten set screws with a drill!
Turn power back on and test.
Always follow safety precautions & Ring's wiring instructions. Use appropriate anchors. Use the correct size Philips driver (PH1 for #4, PH2 for #6) to avoid stripping.
Why Choose the 0-35° Swivel Mount?
Fine-Tune Your Perspective
This Swivel Mount offers exceptional control for minor angle corrections. The 0-35° dual-axis range allows you to precisely dial in the view, ensuring you capture the most critical areas without blind spots, especially when only small adjustments are needed.
Low-Profile & Durable
Its flatter design provides a less obtrusive look on your wall compared to wider-angle mounts. Crafted from robust PETG, it ensures lasting durability against weather, protecting your Ring Wired Doorbell Plus installation for years.
Installation Concept Videos
General installation concept shown below:
Verify Compatibility or Ask Questions!
Double-check your model! Ring names are confusing. If you're not 100% sure you have the Wired Doorbell Plus (formerly Pro), please send us a picture before ordering!
- Email: shop@doorbellmount.com
- Text/Call: 1-833-326-6868
Need adapters for narrow trim? Contact us!
Standard Color: Black. Need a different color? Please purchase the separate Color Change Request listing along with this mount.
Angle Range Note: This mount provides an adjustable range from approximately 0° (flat) to 35° relative to the mounting surface. The exact angle achieved depends on installation specifics.
3D Printed Quality: While 3D printing provides really good production quality parts, there are often minor imperfections that may be found on the prints. These do not impair the function and rarely affect the aesthetics. But if you're not happy with the quality, please text, email, or message me before leaving a review.
Order your 0-35° Adjustable Swivel Mount today for precise aiming of your Ring Wired Doorbell Plus (formerly Pro)!
